Below are the numbers config. in the scanner. they are not a perfect match to the scanners MAP kpa converted; but very near. If you can fine tune them closer, please send me that list.
Note: In my...
Type: Posts; User: LS6DAVE
Below are the numbers config. in the scanner. they are not a perfect match to the scanners MAP kpa converted; but very near. If you can fine tune them closer, please send me that list.
Note: In my...
RamJudd,
Did you ever figure out how to turn off tire pres. sensor feature? I have a friend that is wanting to do this.
Thanks,
I found 1 of the problems-The link that 405HP_Z06 posted is missing a entry for 1.1 volts :banghead: anybody care to guess which way it shifts or does entire table need to be recalulated?
Dave
My tune is getting better every day. But there is one issue that I am having difficulty in resolving. When nailing the throttle-there is a delay (several frames in the scanner) before the commanded...
New numbers (displayed by the scanner program) are nearly the same below 0 psi as the gage. Above 0psi readings still off, and the amount of difference increases as psi increases. I guess I need to...
Thanks! I will try this out after I complete the fuel system upgrades I am presently working on (the car is not running today).
Dave
No info at all! AutoMeter did not know either. I am thinking since the sensor is a GM 3-bar MAP sensor; Chris/HPTuners should have this info, considering 2 & 3-bar OS rewrites. I have contacted...
Hello, I am still having some problems with the configuring of my Autometer boost/vac gage into the scanner. While scanning, gage readings do not match the values in the scanner. I called Autometer...
In my 2-bar set-up, there is a pid in the list named "MAP sensor 2-bar KPA/PSI". All I had to do is select old MAP pid on table-right click-delete-right click-insert-select the Map 2-bar from...
My Z06 will code/activate reduced engine power if the TPS voltage is not at.4-.6 at the throttle stop. What year is your car? Some one will have to help you on your TC issues. Have you tried...
That fixed my problem. Originally I found that I had vacuum leaks,(valve guides, Fast intake) and extra air getting around the blade in the TB. My guess in your situation is a vacuum leak - car is...
Try disconecting the vacuum line to the anti-surge valve. Very gentally test for bucking-remember presure can not bleed off, so be very carefull. If this stops your problem, post results, and I will...
I am ready to pull the motor.....sell car....etc
I know and still knowing how you feel.....I had/have very simular issues a while back in my Mod-nightmare. Since our setups are so much diferent,...
I am dealing with a simular situation on a 90mm TB. Things I do know: TPS voltage at the stop MUST be .4 to .6 volts, and if idle goes to 0% TPS to quick during warm-up, You will not be happy. Very...
Yup, that worked. Thanks! It would have taken a long time to associate that table to the A/C...
Any sugestions on what to change when the RPM dips below comanded idle speed when letting off of the...
I am just getting back to tuning the 2-bar MAP project after some cylinder head problems. The car idles fairly well and I can turn on the AC with almost no noticeable change, however, as soon as...
UPDATE;
To use the single bar MAP you will have to return the MAP sensor cal to stock, the numbers are 94.64 and 10.33. be aware it will only read up to 105 kPa so running in boost you will have...
This may fall under my request for some HPTuners 'skins', but a good dark screen setup option would be very nice. I doubt I'm the only one who logs late at night to try and disturb the peace as...
Chris......The numbers for the 1-BAR MAP sensor do NOT seem to be what I need???
The Z will not run longer than 30 seconds! DTC codes are P0102, P0103, P1514, P0106 and going to REDUCED ENGINE...
Thanks Chris, you saved me hours of hunt and peck time!!!!!!
OK- I understand that I need to turn off the SES light on code P0102....Do I need to do anything to P0101 and P0103 codes?
Can you...
Well, I have figured out how to read, write and write entire VCM (2-bar support), But I am in need of info on how to copy a table from one program and paste into another (timing, ve, or what ever) is...
I have a 99mm MAF that "Pro-M" did the calibration on. I ended up making the housing and they did the cal's. It made some major improvements in my supercharged 02 Z06, that I made some...