Search:

Type: Posts; User: BLP

Search: Search took 0.00 seconds.

  1. I can drive it for days and it's perfect, am data...

    I can drive it for days and it's perfect, am data logging every pid I can think to, give it to customer and within hours it's acting up again. And yes I have also seen much mentioned about the '09...
  2. anyone run into this before? 2009 SRT 6.1 with mods

    Have 09 SRT Challenger, 6.1, rods, pistons, cammed up, Vortech blower, car runs absolutely great, LT/ST trims are under + or_5% 99% of the time, but after it sits a bit you start it and it's surging...
  3. Thread: Startup Issues

    by BLP
    Replies
    2
    Views
    522

    I'm fighting something that might be a similar...

    I'm fighting something that might be a similar cause/fix. We have a 09 SRT, built, stg3 cam, vortech V2, car runs amazingly well, LT/ST never more or less than 5%, problem is warm start, 1st warm...
  4. Replies
    3
    Views
    787

    2000 Dodge Viper Stock File

    Hey does anyone have a stock or modified 2000 Viper file they could share with me? I'd like to get a look at what I can do with HP Tuners before I have the customer ship the car to me as he is 4+...
  5. Replies
    15
    Views
    2,809

    that was a holdover from the original Roush file...

    that was a holdover from the original Roush file I started with
  6. Replies
    15
    Views
    2,809

    So I have the map points working now, definitely...

    So I have the map points working now, definitely a giant improvement everywhere. My issue now is that VCT Schedule Mode is going from working properly to disabled, sometimes right from key on, and...
  7. Replies
    15
    Views
    2,809

    This is the first F150 TVS we have done, and...

    This is the first F150 TVS we have done, and there doesn't seem to be a lot of files out there to compare ours too that aren't originally Roush tunes.
  8. Replies
    15
    Views
    2,809

    Yes I just figured out it was locked on map14,...

    Yes I just figured out it was locked on map14, going to get that figured out, thanks
  9. Replies
    15
    Views
    2,809

    I should also add this file is originally a...

    I should also add this file is originally a dealer installed Roush TVS kit, and I just noticed that while road testing that map14 stays 100%. I realize that many think it a hack to lock one map,...
  10. Replies
    15
    Views
    2,809

    TVS Coyote F150 laying over above 6200rpm

    Looking for some suggestions, have a built 16 F150 coyote, cams, forged bottom, 2650tvs, twin69mm tb, return fuel, that seems to pull like mad all the way to 6200rpm, 640whp, then falls off, here's...
  11. Replies
    14
    Views
    3,520

    PM your email and I can send you a stock file and...

    PM your email and I can send you a stock file and a slightly modified from a 2016 I did
  12. Just had a customer tell me he's got a TRX on the...

    Just had a customer tell me he's got a TRX on the way and wants it tuned, what are we going to need to help him out?
  13. Replies
    2
    Views
    988

    There is a tune file for a Stage3 2008 Shelby...

    There is a tune file for a Stage3 2008 Shelby Super Snake in the tune repository, the Stage 3 could have been equipped with either a KB blower or a TVS the uploader did not mark which blower this one...
  14. Replies
    15
    Views
    3,793

    You also do need to change the exhaust cam phaser...

    You also do need to change the exhaust cam phaser (all the rest of the timing components are the same) at minimum on the Gen2 15-17 F150 motors to the Mustang part number FR3Z6C525B when doing a...
  15. Replies
    15
    Views
    3,793

    All that is for is the mis-fire test it doesn't...

    All that is for is the mis-fire test it doesn't actually change the order, you do unfortunately have to re=pin to get it going as we eventually ended up doing. Total time spent was about 30 minutes.
  16. Replies
    15
    Views
    3,793

    K44 is Correct, that table is only for DTC's we...

    K44 is Correct, that table is only for DTC's we did try it tho as a few people where convinced it would work and hell we like to science.
  17. Replies
    15
    Views
    3,793

    Here are the pin locations for both the Coils and...

    Here are the pin locations for both the Coils and Injectors on a 2016 F150 5.0 vs a 2016 Mustang GT these locations should be the same for 2015-2017 model years, after we re-pinned the harness and...
  18. Replies
    15
    Views
    3,793

    We have found the pinout information we needed...

    We have found the pinout information we needed and are mid way through swapping locations now, if this works we will post the pin info to save others the hassle of finding the info.
  19. Replies
    15
    Views
    3,793

    I am thinking that is what I am going to have to...

    I am thinking that is what I am going to have to do, at this point I am on the hunt for a 2016 Mustang GT ECU pin out, as well as a pin out for the 2016 F150.
  20. Replies
    15
    Views
    3,793

    2016 Ford F150 With Aftermarket Cams

    Hey guys I just put together a 2016 F150 with a set of cams that use the mustang firing order, I am now looking to figure out how to change the firing order as well as the injector firing order in...
  21. Replies
    0
    Views
    1,058

    2018 Frontier, lost cruise control after tuning

    Anyone run into this before, tuned a 2018 V6 Frontier for the manager at our local Napa and his cruise control is inop since, tried going back to the stock file, as well went with our scan tool to...
  22. Replies
    5
    Views
    3,288

    pm sent, thanks

    pm sent, thanks
  23. Replies
    5
    Views
    3,288

    6.7 h&s dual hp pump kit

    Anyone have experience with installing and calibrating a 6.7 with the H&S dual high pressure pump kit installed, 2016 F250, has a SCT in it from before the dual pumps, H&S has warned me to tell my...
Results 1 to 23 of 23