Search:

Type: Posts; User: speedjet

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    4,331

    It was not required to be edit much unless the...

    It was not required to be edit much unless the characteristic of the engine output was changed alot.
    For a ecoboost with bolt-on only required to edit the mid to high-end part. By edit means...
  2. 1st, is the clearance issue. 2nd, you must make...

    1st, is the clearance issue.
    2nd, you must make sure u had fills up sufficient transmission fluid. After certain bare-in time, You need to check the fluid.
  3. Replies
    1
    Views
    970

    1st, you need to add all type of sources channels...

    1st, you need to add all type of sources channels into your log. So others can help u. We can't get any idea from your current log.
    Try adding throttle sources, torque source, fuel source, VCT...
  4. From my easy understanding, the speed density...

    From my easy understanding, the speed density calculator is used to calculate the VE of the engine in order to form the quad, offset, slope tables.
    For the starting point will be adjust the correct...
  5. From my experience, the speed density are not...

    From my experience, the speed density are not required to be change.
    Unless u had make a big changes to the engine. Such as turbo changed to NA or changed super hot camshaft.
  6. Ford ecoboost pocorn and combustion stability limit.

    Hello everyone,

    I recently faced a problem with my ecoboost mustang. I had maxed out all my CSL and LSPI limit.
    Yet I'm facing the CSL limit and cause my throttle to shut off then pedal dead for...
  7. Replies
    11
    Views
    8,528

    I was facing this limit too. The limit will...

    I was facing this limit too.
    The limit will cause my pedal to go dead for few seconds.
    I would like to completely disable this limit. The car was for track only.
    Log attached

    92869
  8. I would recommend you take some time to sort out...

    I would recommend you take some time to sort out your datalog channels 1st. You need to add some important channels and delete others.
    You would need to add torque, throttle, airlimit & fuel...
  9. There is a knock during your 3000rpm to 5000rpm....

    There is a knock during your 3000rpm to 5000rpm. You will need to enrich your AFR in order to get a good combustion to not cause your CAT to overheat due to mixture too lean.
    Especially you had...
  10. Swapping an Auto transmission to Sequential required changing to MT ecu?

    Hello,

    I have a S550 Mustang GT with 6r80 that I'm considering to swap my transmission out to a Sequential transmission or a close ratio MT gearbox for track only.
    All the engine tune was good...
  11. Thread: 6r80 tcc map?

    by speedjet
    Replies
    1
    Views
    1,883

    6r80 tcc map?

    Anyone knows what do this means on 1st & 2nd gear means? 89050

    What if I lock the TCC at 2nd gear do I need to edit all the unlock and slip value to 0 ?
  12. 87624 Same Tipout Limit happen.

    87624

    Same Tipout Limit happen.
  13. Do I need to adjust the Spark Only Ratio Table? ...

    Do I need to adjust the Spark Only Ratio Table?

    Also the mapped points was enable by me from 0-12 and OP. Do you mean that I should disable some mapped points to 6 left?
  14. Tune attached.

    Tune attached.
  15. The actual top speed with this log is 109mph. My...

    The actual top speed with this log is 109mph. My speed limit under speedo was set at 300km/h.
    Is there any speed related limit?
  16. Tipout Limit Problem casuing throttle closing

    Hi all,

    I had a 15GT with whipple SC. The kit run goods with my custom tune but had some problem during the shift after 3rd and into 4th.
    Then there will be a Tipout Limit happens and completely...
  17. Replies
    9
    Views
    2,869

    is all the flare tools limiter disabled with this...

    is all the flare tools limiter disabled with this file?
  18. Replies
    40
    Views
    15,078

    I had a pcm returned to stock and also read the...

    I had a pcm returned to stock and also read the whipple tune. If I flash the whipple tune using hpt into this stock ecu will I still get the flare tools limits? I do not have a flare tools now and...
Results 1 to 18 of 19