Search:

Type: Posts; User: 18f1505.0roush

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. thanks data log looks good after driving today

    thanks data log looks good after driving today
  2. does my ethonal % table look correct?

    does my ethonal % table look correct?
  3. Replies
    6
    Views
    626

    Trying to set this table on mine not sure if this...

    Trying to set this table on mine not sure if this is correct what do you think
  4. Replies
    1
    Views
    407

    [ECM] 20085 - Trans Max RPM After Downshift: This...

    [ECM] 20085 - Trans Max RPM After Downshift: This is the maximum engine RPM that is allowed after a downshift.
  5. Replies
    9
    Views
    444

    will do i follow them on youtube

    will do i follow them on youtube
  6. Replies
    9
    Views
    444

    2018 5.0 with Roush supercharger I'm maxing out...

    2018 5.0 with Roush supercharger I'm maxing out tq tables also Roush only has it tuned to 6500. I have tried to mess with TQ management tables with Inverse tables every time i put it into limp mode....
  7. Replies
    23
    Views
    734

    by the way MCT was the culprit closing Throttle ...

    by the way MCT was the culprit closing Throttle thanks guys
  8. Replies
    23
    Views
    734

    took a while to build THANKS

    took a while to build THANKS
  9. Replies
    23
    Views
    734

    it was the MCT causing the throttle to close and...

    it was the MCT causing the throttle to close and timing cut. Roush has a poor cooler design
  10. Replies
    9
    Views
    444

    email tunes recommended or no

    wanting more out of my Roush supercharged f150. thoughts on a 5star tune or OZ
  11. Replies
    8
    Views
    500

    is RTT os availablefor ford 2018 mustang?

    is RTT os availablefor ford 2018 mustang?
  12. Replies
    4
    Views
    289

    what are your findings on the dyno or real world...

    what are your findings on the dyno or real world testings?
  13. Replies
    9
    Views
    365

    possibly the flywheel

    possibly the flywheel
  14. Replies
    9
    Views
    365

    Its showing cutting spark and closing throttle...

    Its showing cutting spark and closing throttle body for sure
  15. Replies
    9
    Views
    365

    Torque source oscillation, its lost on witch...

    Torque source oscillation, its lost on witch mapped point to use
  16. Replies
    4
    Views
    289

    Speaking of VCT angels

    Putting VCT angles in perspective. The world of TIVCT was and is a game changer for performance and the environment. We can have a custom cams from taps of a key board and control the tail pipe...
  17. Putting VCT angles in perspective. The world of...

    Putting VCT angles in perspective. The world of TIVCT was and is a game changer for performance and the environment. We can have a custom cams from taps of a key board and control the tail pipe...
  18. hello do keep in mind the 5.0 3 gen runs around...

    hello do keep in mind the 5.0 3 gen runs around 15 psi at idle. most likely the PP has a different sender. the new gauge possibly effecting the signal
  19. Replies
    23
    Views
    734

    no ipc showing 0

    no ipc showing 0
  20. Replies
    23
    Views
    734

    by Roush the hp values are set a little higher...

    by Roush the hp values are set a little higher but close the inverse tables are lower than actual load i tried to change the inverse tables doing the math individually but the values are not correct....
  21. Replies
    15
    Views
    1,718

    YouTube video? trying to grasp this thanks

    YouTube video? trying to grasp this thanks
  22. Replies
    15
    Views
    1,718

    Asking also?

    Asking also?
  23. Replies
    23
    Views
    734

    thanks for the help. so you know... I am...

    thanks for the help. so you know... I am manipulating the Roush tune that came with the supercharger kit. it is a safe tune to say in the least.
  24. Replies
    23
    Views
    734

    i have the driver demand torque turned up not...

    i have the driver demand torque turned up not expecting limits there. i haven't done any adjusting with the torque model / inverse tables. i do suspect that's where limiters are coming from but...
  25. Replies
    23
    Views
    734

    o wow thank you ill change that back and keep...

    o wow thank you ill change that back and keep digging
Results 1 to 25 of 58
Page 1 of 3 1 2 3