Search:

Type: Posts; User: Hondaeater

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds.

  1. What version of HPT are you using? Have you...

    What version of HPT are you using? Have you recently updated it or have you always had issues? I would also use a new cable to laptop.
    I also found that the initial updated tune would install when...
  2. Replies
    134
    Views
    20,822

    Unfortunately, LQ9 Tune 4.10 (4.9 log VE...

    Unfortunately, LQ9 Tune 4.10 (4.9 log VE change).hpt is OL if all you did was put that into CL then cool. If you made changes to the OL tune and ran in CL, please post CL tune.
    In CL it only idled...
  3. Replies
    98
    Views
    8,756

    That's exactly what happened on my 1994...

    That's exactly what happened on my 1994 Silverado. I used an anodized loom and it looked great but.... The MSD Super Conductor 8.5mm originally had less than 200ohms resistance and seemed fine. When...
  4. Replies
    134
    Views
    20,822

    I probably was. I have been swamped at work this...

    I probably was. I have been swamped at work this time of year.
  5. Replies
    98
    Views
    8,756

    Are you using the Taylor wires? The 10.5 wires??...

    Are you using the Taylor wires? The 10.5 wires?? If the holders are not sized for those wires or you use some aftermarket goody that runs along the valve covers, the clips/clamps/ holders can pinch/...
  6. Replies
    98
    Views
    8,756

    Delco is good. I use MSD cap and rotor. ...

    Delco is good. I use MSD cap and rotor.
    Curious, how do you have the plug wires supported from cap to plug along motor?
  7. Replies
    134
    Views
    20,822

    i may not have kept up with the issue but when...

    i may not have kept up with the issue but when you start going after the after start table that is in OL. The CL portion takes care of the stoich in fuel trims. Warm startup did you say was lean? The...
  8. Replies
    23
    Views
    2,266

    The Moog/ Federal Mogul parts are high quality...

    The Moog/ Federal Mogul parts are high quality and are made in many factories around the world, including some here in USA factories.

    The R series of parts are for budget minded (cheap) who just...
  9. Are you using the Serial to USB adapters in Win...

    Are you using the Serial to USB adapters in Win 11 without any issues? IDK maybe the 11 Pro version has better driver support for that connection? The cable gets "lost" which has been an issue for...
  10. Replies
    98
    Views
    8,756

    DTC P0300 is set to no error reported so I would...

    DTC P0300 is set to no error reported so I would not expect it to have a CEL lol. Might want to enable that.

    Where is your WB channel? and you are not logging the AFR/ EQ commanded channel? A...
  11. Replies
    53
    Views
    6,080

    I am not at my computer to see file. Are you...

    I am not at my computer to see file. Are you running blended mode both MAF and VE?
    VE only uses the low octane. Burst knock will reduce timing for the quick change of air flow and is what prevents...
  12. Replies
    6
    Views
    759

    Tech man, did you check to make sure that...

    Tech man, did you check to make sure that manifold vacuum line goes to the reservoir tank and the tank, the check valves are good and hose routed to your controls inside it's good? Does the AC/...
  13. Replies
    98
    Views
    8,756

    Is the misfire felt as well as showing up in log?...

    Is the misfire felt as well as showing up in log? Do you get a DTC code?
    In your scanner, can you delete the spaces between channels in the list of you haven't already? Hard to watch data and...
  14. Replies
    134
    Views
    20,822

    Add to the Fuel> OL > EQ ratio. When things are...

    Add to the Fuel> OL > EQ ratio. When things are cold and dry surfaces, fuel sticks to the intake tract and only a portion makes it into the cylinder for combustion. What you need to do is add fuel in...
  15. Replies
    134
    Views
    20,822

    I see where it went lean on tip in. I did not...

    I see where it went lean on tip in. I did not have time to look over the previous iterations to see the log of part throttle and the idle at the end. It would show if the offfset table needed to be...
  16. The fact you had no problem for 500 miles and now...

    The fact you had no problem for 500 miles and now you do.... Did you change the way you drove, how much throttle you gave it now that it is broke in?
  17. P1516 not p1514, setting the engine diag airflow...

    P1516 not p1514, setting the engine diag airflow up to 3 g/s for p1516??
    May not work. Of course try it but....
    Stroh I do recommend, since this is a TAC related issue p1516, you solve the...
  18. Replies
    134
    Views
    20,822

    1) VE , I recommend the 15, 30, 45-50. Once you...

    1) VE , I recommend the 15, 30, 45-50. Once you get the bulk of the table done like this you can go back and go in-between if needed. I would shoot for +/- 2-3 percent. Do it all in the same day if...
  19. Replies
    98
    Views
    8,756

    Go into Exhaust tab and raise the EGR Min VSS...

    Go into Exhaust tab and raise the EGR Min VSS speed and Diag Ebnable speed to 200 or more since THIS IS FOR OFF ROAD USE ONLY.
    P0401, 404 and 405 no error reported, you did block that EGR off right?...
  20. Replies
    3
    Views
    465

    You need to add a lot of channels to your Scanner...

    You need to add a lot of channels to your Scanner list. Try these 135056.
    It is almost too many channels for Gen3 bandwidth but it will get a good baseline.
    It was already mentioned, you need to...
  21. Are you using Windows 11? You say it works if...

    Are you using Windows 11?
    You say it works if plugged in and restart? Good to know. I have not made the upgrade to Win 11 yet because of the issues I hear. I use the prolink cable and have not had...
  22. Replies
    134
    Views
    20,822

    HHHAAAHHHAAA I know! It was getting long and...

    HHHAAAHHHAAA
    I know! It was getting long and probably lost a few people on the way.
    I will provide cliff notes upon request lol.
  23. Not sure why the Engine Diag MAF Hz fail set to...

    Not sure why the Engine Diag MAF Hz fail set to 0hz when Dynamic high rpm is set to 4000, it is not set for MAF only OR VE only, and the DTC is set for NO MIL Light. Change p0101-p0103 to mil on 1st...
  24. That is a perfect explanation of a complex...

    That is a perfect explanation of a complex system! Cool. Mixed up primary and secondary sensors, lol.
    Turn on the kitchen sink and wonder why the bathroom water starts running lol.
  25. Replies
    134
    Views
    20,822

    These courses right here are FREE and very...

    These courses right here are FREE and very informative, I recommend everyone starting out tuning get this BASIC knowledge to begin learning to tune EFI. You have done pretty well researching but you...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4