Search:

Type: Posts; User: Yeti ChipTuning

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. probably is late..but I can

    probably is late..but I can
  2. Replies
    87
    Views
    51,360

    how you can connect to the ecu without obd port...

    how you can connect to the ecu without obd port ?can some one share the pin-out
  3. Replies
    3
    Views
    2,422

    can you attach the stock file ?

    can you attach the stock file ?
  4. rise a 7000 rpm the tcm limit and the rpm limit...

    rise a 7000 rpm the tcm limit and the rpm limit in EOT ECT , set the rpm limp of 200 rpm and you got it
  5. HaasExp you have tuned the engine ?

    HaasExp you have tuned the engine ?
  6. Replies
    60
    Views
    23,344

    yes sorry but I have found this info really...

    yes sorry but I have found this info really helpfull and I'm going out of the thread
  7. at the moment nope only with winols an my finger

    at the moment nope only with winols an my finger
  8. Replies
    20
    Views
    20,691

    we must wait , I have send the solution at the...

    we must wait , I have send the solution at the tech ,or you can set the sitch at 16 absolute value the switch with winols
  9. Replies
    60
    Views
    23,344

    this is an awesome description , than the min and...

    this is an awesome description , than the min and max overlap work even in the Nag1 right ?, but you speak about overlap time , and overlap torque right ? if i lower the low time and torque ,I allow...
  10. Replies
    9
    Views
    3,174

    545 RFE Dyno enable

    hi , i'm new to Chrysler Transmission but this parameter it intrigued me, can someone explayn what really do ?

    thank you
  11. Replies
    6
    Views
    2,706

    i have found the issue and have emailed the...

    i have found the issue and have emailed the solution at the tech , hope is corrected in few time
  12. Replies
    60
    Views
    23,344

    Jim P thank you so much for all this info ,...

    Jim P thank you so much for all this info , really help
  13. ok set at 16 bit absolute value , I have disabled...

    ok set at 16 bit absolute value , I have disabled the downshift at wot with autostick , How i can open a ticket for correct this in vcm suite ?
  14. Replies
    19
    Views
    15,570

    you loose engine brake

    you loose engine brake
  15. Replies
    19
    Views
    15,570

    never tryed to apply over the tcm rpm limit and...

    never tryed to apply over the tcm rpm limit and release at low rpm ?
  16. ok , I have had a time to play , but vcm editor...

    ok , I have had a time to play , but vcm editor fail in some switch , example in Shift tq adapt downshift and upshift and tq red enable disable dwn /up shift , fortunally I use WinOls too and i have...
  17. torque reduction yes , I know , but the torque...

    torque reduction yes , I know , but the torque adapt enable /disable is in the shift properties , i do a try disabling it in downshift and see what happen
  18. question , the Shift Tq adapt 2-1 and so on , is...

    question , the Shift Tq adapt 2-1 and so on , is the torque loss for command the down shift from 2nd to 1st gear ?
  19. rised the tcm rpm limit over engine rpm limit ,...

    rised the tcm rpm limit over engine rpm limit , autostick at wot ,set enbaled, disabled the performance driving and fine work on part throttle shift table for performance ,plus TCC apply and relase
  20. for what i have undrestand the S-C and M is...

    for what i have undrestand the S-C and M is correlated than in M with autostick when I stop the car S or C is autoengaged or I'm wrong ?
  21. NAG1/A580 autostick like manual transmission ?

    Hi , I have tryed some trick and I'm able to use the autostick without auto up/down shift and use like a manual stick, but...
    if i'm stop the car the transmission downshift , example I'm in 3rd gear...
  22. you haveread from obd or pinout ? I'm search the...

    you haveread from obd or pinout ? I'm search the pinout for this tcm
    thank you
  23. Thread: P061b

    by Yeti ChipTuning
    Replies
    2
    Views
    1,580

    is the Torque monitoring error , maybe is a tuned...

    is the Torque monitoring error , maybe is a tuned engine ?
  24. Replies
    0
    Views
    837

    Egs 52/53 pinout

    hi , as written in the title ,I need to know the pinout connection for this TCM , I need to work on the bench

    any help is really appreciated

    Marco :hi:
  25. Replies
    2,288
    Views
    1,644,163

    Sticky: Hello To all , I'm Marco from Italy ,hope this...

    Hello To all , I'm Marco from Italy ,hope this community can help me to understand how best to use this tool
    cheers
Results 1 to 25 of 26
Page 1 of 2 1 2