Cool thats all I need to know.
Has anyone tried to manually concatenate them and see if it works before I try this myself and attempt to figure out if there is a manual way.
Dixit
Type: Posts; User: Dixit
Cool thats all I need to know.
Has anyone tried to manually concatenate them and see if it works before I try this myself and attempt to figure out if there is a manual way.
Dixit
Not sure if this is already there and I dont know how to access it, but I thought of how cool it would be to allow one to concatenate the scans I do at times to look at more data all at one time, I...
I went circles around this setup and ended up removing them as I just could not continue with them anymore cause the rich decels were causing major surging issues upon returning to the accelerator. ...
I tried these and never got an offset table that I could get working 100%. Chris recommended the only way around my rich decel issues were caused by not being able to command a small enough pulse...
I guess cause alot of people dont want to rip the LS7 apart just to get the 24x reluctor on and make sure its positioned accurately.
Well I have played with the DFCO but that is not the answer, right now it kicks in right around 2100rpm, if I drop it to say 1500, then it starts hampering driveability.
You mention the stock...
What I would do is if your STFT are within +/- 10 right now, disable your LTFT and get your STFT as close to 0 and -4 as possible, which is alot quicker than waiting each time for the LTFTs to learn...
At this point my option is to remove the injectors and drop in a pair of SVO30s. And then when I get the TT kit on there put a vacuum referenced fpr, another option is to just use a normal FPR and...
Ken, How do I get those Offset specs? The only specs on that injector that they show are as follows:
Static flow 10.8g/sec @ 600kpa
Gain=0.110ms/mg
Offset=0.055ms
Turn on Time=1.14ms @ 14VDC...
Heres my latest tune.
So you got the same problems with your SVO 42s? This is not right. I mean even if the injector is too big for these mods/engine setup that shouldnt keep it from working.
...
Well not sure how many have followed my thread on LS1tech.com but I thought Id see if the masters at HPtuners can help me out on this.
I basically installed 60lb mototron injectors and then...
Are they really $100? Last time I checked I thought I saw used car places trying to sell them at $400-500.
Talked to a chip/rom geek friend of mine and I told him Ive probably flashed my Z06 VCM well over 400 times so far with all the tweaking and changes I keep making to get it riding like a champ. He...
I remember Chris talking about implementing this in the features forum and I see it there but not sure if it works. I set it to enabled and RPM at say 3000 and the shift light does not blink.
In...
Also I think many forget to remember that when doing this you want to make sure both your fans are OFF and AC is off. If your FAN1 is on then it throws that STIT/LTIT value off. Use your VCM Controls...
No, if your LTIT is -1.80, then you subtrace your current value from that. IE, if your value at that temp is say 10.80, then you subtract 1.80 from it and you will be at 9.00.
Or just use the...
Id look at your IAC and make sure you inline, seems like thats off since you have to keep the throttle open.
Also maybe adjust your Base running airflow table as that definetely has changed....
Even if linux killed the VMWare you would techincally still be fine because normally you should be using the Calibration writes, not the entire VCM write. If your laptop died during a calibration...
On the C5s you cannot disconnect the MAF because it has the Intake Air Temp sensor built into it.
All you have to do is put the MAF Fail Freq to 0. Then you will be in SD mode for sure.
Dixit
Sorry to bring this thread back but when you say this will be your next position during restart.
How exactly do we tweak this table? I ask because alot of sites show if you install a cam raise all...
Right but if they are still say over +5 LTFTs, then I need to scale the MAF a bit more dont I? I mean if the VE table is onpoint in SD mode, then when the MAF is connected and it throws it all off, I...
Man I cant thank you enough for helping me through this mess.
When you say scale the MAF table up or down, we talking the entire table by 1-5% or so Until I get the LTFTs between +/-5.
Again...
Okay, so its definetely making changes to the table via percentage, not just simple subracting the final learned by half. This makes alot of different in many cases.
So you are saying when the...
Im not sure if there is a confusion on this or is it just in my thick head,
But if the LTFT/STFT histrogram is in percentage, then shouldnt you be doing a calcuation when making the change to the...
Ive been getting this code about 1-2times a week. If I clear it, it comes back after a few days. So I know its a problem and not sure why though. I made changed to the VE table quite a lot but...