I have swapped O2s. Not on the 6.0. But the 5.3 I have. And things changed. But I put new O2 sensors in both sides of the 5.3L.
Type: Posts; User: cjsgarage
I have swapped O2s. Not on the 6.0. But the 5.3 I have. And things changed. But I put new O2 sensors in both sides of the 5.3L.
Yep. I?m aware of this. I?m 99.99% sure neither applies.
The 5.3 ran perfect before it got the blower. Then it spent time at a paint shop. And now it?s acting strange.
The 6.0 I did rebuild the...
I did try new O2s in the Silverado OS car, also. Also put a new fuel pump in it and I’m going to try injectors. I can’t give these cars back the fuel control cause it makes them sluggish. I don’t...
Thought I posted this, but maybe my laptop died and I forgot. Who knows?
I have had it on two cars in a row now. One Gen III 6.0 LQ9 with an ASA cam. Os is a 2001 Yukon Denali. Tried replacing O2...
I've had an issue where I can't remove the VATS on E38 and E67 ECMS, but now I'm also having a weird anomaly with B1S1 always reading -38% on the STFT. It doesn't make sense to have it be three cars...
Support is of no help so far.
Doesn't work in any combination of factors if I Write Entire or Write VIN/Tunerlock/VATS or Write Calibration. Doesn't matter if I flip one switch or all of them....
I did go back an make sure the Starter Diag was disabled and did another write entire. Still no go.
I?m definitely using a newer version of the software now, but I don?t know to go back to an older one unless someone has a copy they?d like to email over.
I put in for a support ticket, but it?s...
edit: deleted for double post
Ben,
just triple checked that they're disabled now. Still no luck. Even tried it in another car in case it was a harness issue.
two stock harnesses and one aftermarket, yes.
I'll triple check the starter relay checks in a bit here.
THANK YOU GUYS for helping me. I did finally put a support request in.. as i tried a...
It won?t even crank.
It?s like the edits I make don?t write.
I turn off vats 1 and 2, and starter checks. But it won?t crank and it continues to complain about the VATS in the display.
I?ve...
They?re set to not have VATS. Turning them on would make it never start. But I do know what you mean.
I haven?t. It takes ages and the help here is usually faster. Do you happen to have a copy of your version of editor you could email over? I?ll try support, too.
what's your method? since I can't seem to get it right..
did this and then did another write entire. still no go.
Put a known good ECM into the car, and it cranks. But neither of ones I flashed to remove VATS crank the vehicle.
Both of them are in current cars. So they would have controlled cranking, if that...
did you, by chance, take your editor out of "advanced" mode?
I've searched and searched and done what the write ups said. I've been tuning for a long time and never had any problems until this month.
the last two E38's I needed to unlock for swaps didn't...
racepak has always worked well for me
Anyone got any advice?
I swapped for an 08 ECM and it?s now reading trans current gear and PRNDL status. Trans Shift Mode is still ?Unknown: 0B?.
Still won?t shift out of 2nd on its own. Can...
I should add: it has a TCM that came out of a 2007 Saturn Aura. At least, that's what the paint marks on it say.
I can only assume the ECM came out of a 2009 Silverado, as that's what it was when...
hey guys.
I'm pretty competent around this tuning stuff, but this trans set up has got me really messed up. Contemplating buying a new-to-me TCM and ECM.. it's that bad.
The computers are...
I?ve got C1 all done. But there?s 3 pins that are not present that I?m not sure what they went to:
C1 42 brn/wht sensor ground
C1 48 brn/db 5V supply
And
C1 54 brn/tn sensor ground
Anyone else...
I downloaded some from alldata. Hopefully those work. I did see that the grounds are in common on the sensors, but the only schematic I found (at first) was to a Mopar Performance PCM.. and the...