Search:

Type: Posts; User: iceman321

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    496

    [QUOTE=veeefour;760530]yes[/QUOTyes very funny....

    [QUOTE=veeefour;760530]yes[/QUOTyes very funny. Do I need to send it for an unlock?
  2. Replies
    2
    Views
    496

    2022 Whipple calibration

    Can the whipple calibration be read,adjusted and flashed or is flashing the PCM impossible without sending it in for an unlock?
  3. Replies
    0
    Views
    1,478

    Post moved

    Post moved
  4. nothing yet

    nothing yet
  5. any luck yet? I have not tuned gen 1 but on gen...

    any luck yet? I have not tuned gen 1 but on gen 3s the driver demand table has to be raised or the power will cut off hard, yours looks like it needs to be adjusted. I would also leave cylinder air...
  6. Replies
    9
    Views
    1,401

    If you haven't made any changes other than the LT...

    If you haven't made any changes other than the LT exhaust, you shouldn't have any issues, even without tuning, transport delay alone won't cause any real problems.
  7. Replies
    12
    Views
    1,900

    look around locally for a used 18 Int. manifold....

    look around locally for a used 18 Int. manifold. Upgrade injectors, get a flex fuel tune and you're set for N/A. if you're buying a new intake I recommend a ported boss, cheaper than the 18, and in...
  8. Replies
    11
    Views
    5,988

    To my understanding the borderline is your...

    To my understanding the borderline is your base/floor, spark can dip lower than the borderline, but not higher than MBT maximum brake torque. Tables 0 to 13 are there for imrc closed, 14 to 26 open...
  9. serious tuning Question about Speed Density tables gen 1 to 3 coyotes

    I noticed a lot of people get mail order tunes, given that the tuners don't request actual MAP sensor data, do they 1) rescale to the new boost levels and interpolate the data already in a calculator...
  10. torque management >general>unsaturated switch and wheel torque reserve

    Enabled vs Disabled, what changes?
  11. its a centrifugal ess pushing 14 psi at 7000, I...

    its a centrifugal ess pushing 14 psi at 7000, I was going to go with my other pulley that makes about 8 or 9psi at 7000rpm and rev it out to +7500 instead. Its just that when I was N/A power died...
  12. thanks for the input. So in that case, what im...

    thanks for the input. So in that case, what im seeing is that in order to make the intake valve open later aka "retard" the timing, one would be adding to the original values of the Ivo OP table to...
  13. 2018+ cam advance/retard adjustmentt question

    1. these are actual crank angle as the description at the bottom of the screenshot claims. IF so that means NEG for intake and NEG for exhaust are both referring to btdc exhaust.
    2. what I think it...
  14. Replies
    43
    Views
    5,102

    Disable anti shuffle and correct your...

    Disable anti shuffle and correct your torque/inverse. you have a throttle angle error of -11 at 3k rpms
  15. Just go back to stock intake+TB check all your...

    Just go back to stock intake+TB check all your hoses, clean MAF, check plugs ect. make this easier on yourself and your tuner. once its good work on the upgrades.
  16. the injector flow rates do not look anything like...

    the injector flow rates do not look anything like 2000 cc flow rates, use the manufacture data and zero in from there, i shouldn't need much adjustment depending on the fuel psi, worst ive seen is...
  17. Im not sure you were adjusting your maf correctly...

    Im not sure you were adjusting your maf correctly as it looks like your lb/s are pretty high. If you multiply by % >120979
  18. If you're trying to correct fuel trims because...

    If you're trying to correct fuel trims because you're trying to dial in injectors you don't need to mess with the MAF data, generally speaking you adjust your injector slope high for acceleration:...
  19. desired brake torque vs engine indicated torque reference vs etc torque request.18GT

    all PiDs have different readings under key on engine off conditions, is the difference between scheduled torque and engine torque the only thing that needs to be zeroed to reduce wheel torque error...
  20. Replies
    2
    Views
    1,153

    what a difference, what method was used for...

    what a difference, what method was used for smoothing? did you do simply smooth the entire table? I find that usually causes the lower rows to change alot.
  21. Question about torque and inverse tables

    Is there a list of what circumstance each table belongs to? and if one wants to get rid of a table is it as simple as zeroing the table or further adjustment necessary like playing w the distance...
  22. Replies
    10
    Views
    2,364

    its likely the torque and inverse tables, use...

    its likely the torque and inverse tables, use your stock tables to see if u notice the improvement(it wont make power but will drive better)
  23. fuel rail pressure wont stop rising after supercharger install!!goes past 3000

    117469 installed a centrifugal supercharger, now the car cant regulate the fuel pressure, over 10 minutes the rail goes past 3500psi! causing major issues in stop and go traffic
  24. whats the min duty cycle set to?

    whats the min duty cycle set to?
  25. Replies
    3
    Views
    1,680

    did you input all the data for the 47s? you cant...

    did you input all the data for the 47s? you cant just drop in new injectors and use the maf to correct afrs.
Results 1 to 25 of 37
Page 1 of 2 1 2