Search:

Type: Posts; User: vortech

Page 1 of 14 1 2 3 4

Search: Search took 0.00 seconds.

  1. What is the MPVI3 Resynch procedure-keep getting disconnected?

    What is the resynch procedure for the MPVI3. Not sure if I have been doing something wrong, but I have had to disconnect the unit from the car and my lap top, then reconnect with my laptop to resynch...
  2. Can an RTD device be used to tune more than one vehicle?

    Just wondering if an RTD device can tune more than one vehicle if you buy more credits for it or do you have to buy a separate RTD device?

    Thanks!
  3. 2010 5th gen Camaro header intake tune advice

    Hi Guys, I'm hoping I can some pointers to tune 2010 5th gen V6 A6 Camaro with a set of ARH headers and CAI. I've tune alot of cars Gen3, 4 and 5 but this is a first for me.

    When I pulled the...
  4. So by turning the Supercharger tab to none it...

    So by turning the Supercharger tab to none it runs in all airflow modes. However in NA-TIAP and the factory SC-SCIAP-TIAP modes it keeps throwing the codes P10BC and P2635. the dash does goes into...
  5. I have tried running it in OE mode but it would...

    I have tried running it in OE mode but it would go into rep because it was looking for the bypass valve feedback even with the codes disabled. What I didn't do was tell the car it no longer had a...
  6. 19 C7 Z06 A8 Cam'd and Procharger-what MAP sensor config?

    On a 19 C7 Z06 LT4 that is cam'd and Procharged what map sensor config are you running? The factory SC-SCIAP-TIAP or NA-MAP?

    If N/A map then why do we need the TMAP anymore?

    TIA!
  7. Replies
    238
    Views
    232,965

    I keep getting the Windows cannot access the...

    I keep getting the Windows cannot access the specified device, path, or file. You may not have the appropriate permission to access the item.
  8. It's funny you mentioned the torque tube. My car...

    It's funny you mentioned the torque tube. My car is C7 Z, the torque tube is actually carbon fibre and the transmission end was broken. Since I mostly drag this car I did not see the need to replace...
  9. I've attached another tune and log-this time i...

    I've attached another tune and log-this time i turned off the knock sensors. Result was no knock-I also recorded a tailpipe video and no "puffs" were visable. Something is making the knock sensors go...
  10. Massive knock retard with 2650 from 4400 to 6000

    I'm confused as to what could be causing all this knock retard. What has me confused is it does it on pump, pump and meth, and even on E. Pretty much at the same spot. 4400-6000. I've tried more...
  11. Replies
    4
    Views
    1,211

    Can you run these cars like a flex fuel GM car or...

    Can you run these cars like a flex fuel GM car or do you need to run a separate tune for E85?
  12. Can pull and edit 2021 Mustang tune but unable to scan or log needed channels

    I just picked up a 2021 Mustang GT. I was able to pull and edit the tune but I am unable to log the channels for a layout I had made for a 2018 to tune. Not sure what I'm doing wrong?

    TIA
  13. Replies
    0
    Views
    466

    Are 2021 Mustangs tuneable?

    Just wondering if 2021 Mustangs are tuneable yet?
  14. Replies
    8
    Views
    1,097

    Here is log file

    Here is log file
  15. Replies
    8
    Views
    1,097

    TMA kicking in at hi-rpm?

    I?m having this weird issue where torque management advance is kicking in around 6100 rpm and pulling 9 degrees of timing. You can clearly see this blip on the dyno graph. This is the 2nd time I?ve...
  16. 17 6.2 Crew Cab Max drive shaft speed when dynoing

    Just wondering what the max safe speed is to run a 6.2 Crew Cab on the dyno so you don't lose a driveshaft. Are you guys doing them in 5th or 6th gear-TIA!
  17. FP spikes to 5000psi then stuck at 3500psi after dyno pull with LT4 inj/pump upgrade

    2018 GS here with a P1X, BTR cam and LT4 inj and a pump, DSX low side. Just made a dyno pull to 5k and when I let off the Fuel Pressure spiked to 5000 psi then dropped to 3500 psi till I shut the car...
  18. Any update on this-running into the same issue

    Any update on this-running into the same issue
  19. Rear 02's disabled but codes still popping up even after set to no error reported

    Just a simple tune on a pickup with headers, no cats, no rear 02's. Will throw codes for P036, P037 then run rough. Codes are set to no error reported but they are still reporting. Anyone know what...
  20. Can't read or write 19 trans tune with MPV1 after latest updates

    Anyone else having this issue? I cannot read or write 19 transmissions tunes with the MPV1 after the lastest update. Not the working version or the BETA. MPV2 will however read and write it.
  21. I'm pretty sure table 40740 would limit WOT in...

    I'm pretty sure table 40740 would limit WOT in stock form. Did anyone notice that as well?
  22. Best way to limit torque/throttle to get traction

    So this is the opposite of what most folks want. On a prepped surface I can get my throttle to open immediately to get hi 1.2's-low 1.3's sixty's. I now want to be able to limit the throttle/torque...
  23. Replies
    12
    Views
    9,904

    I asked this recently and they said they don't...

    I asked this recently and they said they don't have to plans to-but we know that can change. The ECM case has E90 engraved into it-it looks just like a E90 but uit does say that it is a E93. The...
  24. I mentioned that in my original post, my TCM has...

    I mentioned that in my original post, my TCM has been unlocked by HPT. Again I can write a tune to it, I just can’t read it.
  25. Weird issue, can?t pull TCM tune but I can Write it.

    I?m having a weird issue that just started recently. I can?t read or pull TCM tune but it will let me write a saved TCM tune. Just started happening recently. 19 Z, unlocked TCM.
Results 1 to 25 of 326
Page 1 of 14 1 2 3 4