Search:

Type: Posts; User: tramotorsports

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Powerboost file attached... 133934

    Powerboost file attached...
    133934
  2. Replies
    14
    Views
    1,754

    do the throttle relearn. It won't work with just...

    do the throttle relearn. It won't work with just one click though. you have to click the button over and over again about 30 times for it to actually work. Good Luck!
  3. Replies
    1
    Views
    1,402

    2016 C7 8L90 TCC lockup issues at WOT

    Has anyone had issues on the C7 platform getting WOT lockup with their torque converter. Works flawlessly everywhere except at WOT.

    Circle D 258mm Pro Series currently installed. Switch from a...
  4. same issue. bump.

    same issue. bump.
  5. Replies
    8
    Views
    2,073

    Im having same issue on two turbo cars currently....

    Im having same issue on two turbo cars currently. This ?transfer case? limit never presented itself until recently. I can?t seem to get around it at the moment. When active it pulls 4-5* of timing...
  6. Bump. No luck on gen 1 control pack ECU either

    Bump. No luck on gen 1 control pack ECU either
  7. Replies
    20
    Views
    6,189

    https://www.diyautotune.com/product/99-04-v8-musta...

    https://www.diyautotune.com/product/99-04-v8-mustang-gt/

    This fixed all the tuning problems I was having.
  8. Replies
    20
    Views
    6,189

    I've attached a datalog with the issue I am...

    I've attached a datalog with the issue I am having along with associated tune files...
    9321993220

    You can see STFT's are at +40-50% immediately after startup for about a minute straight. Full...
  9. Replies
    20
    Views
    6,189

    93213 Tune file attached. Proceed with caution...

    93213

    Tune file attached. Proceed with caution it is a problem child.

    Mods:
    Built engine with cams
    Procharged
    ID1050's
    Fore twin 465 return system
  10. Replies
    20
    Views
    6,189

    I'm having same issues with no luck. About to...

    I'm having same issues with no luck. About to throw in the towel on this.
  11. Replies
    42
    Views
    21,789

    This has been the fix for me.

    This has been the fix for me.
  12. Replies
    2
    Views
    4,855

    4R200 tuning

    Has anyone dabbled in this yet? We have a Coyote Fox swap coming to a close equipped with a PBH 4R200. Hoping we will be able to get this dialed in properly ourselves. If anyone wants to assist or...
  13. Replies
    15
    Views
    8,453

    I?ve got one running a flex tune now. We are...

    I?ve got one running a flex tune now. We are currently doing HPFP, injectors, lift pump, and BAP as we speak. We limited out our fuel sustem quite easily going to E. Hope this alleviates it.
  14. Replies
    9
    Views
    4,373

    It is commanding leaner because your fuel trims...

    It is commanding leaner because your fuel trims are negative. it is commanding a leaner value simply to maintain your target EQ ratio. These cars stay in closed loop at WOT so the indicated command...
  15. Replies
    2
    Views
    1,305

    Ecoboost flex fuel support

    Any ETA on this? Would really like to give it a shot on a 2018 Raptor.
  16. Replies
    5
    Views
    5,036

    I'm in the same boat. Can't seem to get it...

    I'm in the same boat. Can't seem to get it working properly.
  17. Replies
    70
    Views
    127,440

    Sticky: Anyone have luck using this calculator on 15+...

    Anyone have luck using this calculator on 15+ Ecoboost vehicles? Every time I calculate coefficients I'm getting some crazy numbers automatically popping up where I've already made changes...
  18. Not sure if its like the other Chrysler PCM's but...

    Not sure if its like the other Chrysler PCM's but if so, set the engine displacement to 0. I think its under Engine-->General tab.
  19. Replies
    30
    Views
    10,835

    Assuming you weren't able to read the file?

    Assuming you weren't able to read the file?
  20. I sometimes use his spreadsheet as a starting...

    I sometimes use his spreadsheet as a starting point if I'm building a new base. All other changes come from driving the vehicle and actually feeling it. Leaving converter unlocked in the lower gears...
  21. Replies
    2
    Views
    1,289

    Agreed. Should work through the scanners functions

    Agreed. Should work through the scanners functions
  22. Replies
    6
    Views
    7,254

    Agreed, I try getting my customers into a...

    Agreed, I try getting my customers into a converter and gear swap before any other modifications.
  23. Why did he do that? Why not leave the stock tune...

    Why did he do that? Why not leave the stock tune in and just properly tune the car for the new parts?
  24. Replies
    2
    Views
    2,130

    I was right under $40k for an MD-250 at the end...

    I was right under $40k for an MD-250 at the end of 2016. Almost pulled the trigger before I found a slightly used one for almost half that price. I tune around 4 cars per week and haven't had a...
  25. Replies
    2
    Views
    1,870

    And make sure the EVAP solenoid valve is still...

    And make sure the EVAP solenoid valve is still installed. Had a car come in for dyno the other day that the valve was simply omitted and the EVAP line hooked directly to the intake manifold. massive...
Results 1 to 25 of 176
Page 1 of 8 1 2 3 4