Search:

Type: Posts; User: lukearmstrong1990

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds; generated 58 minute(s) ago.

  1. Replies
    3
    Views
    1,437

    knock sensor gain way too sensitive. disable...

    knock sensor gain way too sensitive.

    disable burst knock

    set 45kpa up gain to 1.1 and below 45 kpa to 8 and see how u go.
  2. wheel speed cutoff rpm limit?

    wheel speed cutoff rpm limit?
  3. Replies
    6
    Views
    1,559

    log idle trims (STIT) your throttle is at 2%...

    log idle trims (STIT)

    your throttle is at 2% from start up. needs to be 0% so it enters correct idle stratergy.
    looks like it needs more air as the IAC is wide open. add some BRAF. you may need...
  4. 11:1 comp, pump fuel and 28 degrees.... wow

    11:1 comp, pump fuel and 28 degrees.... wow
  5. Replies
    1
    Views
    784

    "go advanced" and attach tune file to post

    "go advanced" and attach tune file to post
  6. tune file?

    tune file?
  7. 101399

    101399
  8. if u want SD apply the custom OS, so much better...

    if u want SD apply the custom OS, so much better IMO
  9. hit apply 2 bar os. save file. close file. re...

    hit apply 2 bar os. save file. close file. re open file. edit and then write entire to put the PCM into custom OS
  10. 101387101388 with IAT multiplier 1101389

    101387101388

    with IAT multiplier 1101389
  11. yes use the flex fuel table to add spark for...

    yes use the flex fuel table to add spark for ethanol. the multipliers for MAP and composition look good. but you could be adding 3 or more degrees from 2400rpm and 0.68-0.72 area and up. and an...
  12. post latest tune. i would suspect the drop in...

    post latest tune.

    i would suspect the drop in torque is due to reduction in timing. less timing car knows its producing less torque. as timing goes back up so does torque. you can see thats...
  13. spark doesnt care about Closed or open loop or PE...

    spark doesnt care about Closed or open loop or PE or BE. it does whats in the main tables influenced by all the relative corrections.

    try smooth the transition in your main spark tables where its...
  14. log all TM channels and post that log. looking...

    log all TM channels and post that log.

    looking at your latest log...04.52.454 second point. 0.96g/cyl 2671rpm closed loop pre PE. high octane requests 5.5 degrees. log shows 4.5. IAT is asking to...
  15. yes, but try those other suggested changes &...

    yes, but try those other suggested changes & report back
  16. disable fast torque exit zero burst knock out ...

    disable fast torque exit
    zero burst knock out

    iat compesators are too aggressive.

    also your low octane table has no timing where your problem is. copy the high over to tune it.

    log all...
  17. tune file?

    tune file?
  18. can cheat and set adaptive idle to be active from...

    can cheat and set adaptive idle to be active from 60mph and it will fix it

    sounds like too much air as it hangs above targeted rpm with little timing. vac leak or too much base running air
  19. close throttle blade and get warm idle on target...

    close throttle blade and get warm idle on target rpm with IAC at about 80-100 steps with 10-13 degrees.

    its got too much air and until it goes into adaptive idle it cant control idle rpm

    make...
  20. file

    file
  21. Replies
    2
    Views
    986

    disable stall saver. set idle spark...

    disable stall saver.

    set idle spark corrections back to stock

    remove 30% base idle airflow from park column

    set idle spark in park/N to 5 degrees less
  22. Replies
    7
    Views
    5,833

    needs more air. needs enough to idle at like...

    needs more air.

    needs enough to idle at like 10-13 degrees warm, not 20.

    disable rolling idle, disable stall saver.

    make sure fueling is bang on and up the warm idle to 850 plus rpm.

    log...
  23. disable injector de soot switch disable fast...

    disable injector de soot switch

    disable fast tq exit and max the values

    set dynamic disable and re enable to 8000rpm under airflow dynamic
  24. disable brake tq managment and max out table

    disable brake tq managment and max out table
  25. Replies
    2
    Views
    2,592

    your wastegate DC is maxed out. why?

    your wastegate DC is maxed out. why?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4