Search:

Type: Posts; User: 8850

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    5
    Views
    231

    :)

    :)
  2. Replies
    5
    Views
    231

    You need to log manifold temperature. That is...

    You need to log manifold temperature. That is what is pulling your advance. There are two. The one that rises with boost is the controlling.
  3. https://forum.hptuners.com/showthread.php?55825-55...

    https://forum.hptuners.com/showthread.php?55825-55825&p=416621&55825-55825&p=416621#post416621

    After you get your configuration and log then to correct your table Open your file. Change the drop...
  4. You are correct, sorry. I think then I would...

    You are correct, sorry. I think then I would change your throttle from 37% to 100% all the way back down to 0. Right now you don't open until 2400 rpm. Engine, airflow, electronic throttle, max %.
  5. Try lowering the TM upshift torque factor on the...

    Try lowering the TM upshift torque factor on the 1-2. I would start with .5000.
  6. Replies
    2
    Views
    146

    Awe! Very good! Thanks! For this table:

    Awe! Very good! Thanks!

    For this table:
  7. Replies
    2
    Views
    146

    How to reduce advance in spark table?

    Is there an easy way to reduce all of the highlighted by a couple degrees without reducing one at a time? We don't have a minus command.
  8. I disabled converter lockup for 1-6 gears. Only...

    I disabled converter lockup for 1-6 gears. Only lock in 7 and 8th. Drives much nicer.
  9. Replies
    4
    Views
    594

    Maybe this will help: ...

    Maybe this will help: https://forum.hptuners.com/showthread.php?55825-55825&p=416621&55825-55825&p=416621#post416621
  10. The EIO plugs into the side of your MPVI. ...

    The EIO plugs into the side of your MPVI. Doesn't really matter where you get power from as long as it's a keyed source in-case you forget to unplug or turn it off.
  11. I used a red wire because that's what I had but...

    I used a red wire because that's what I had but white goes to #1 in the EIO plug. Cigarette lighter connector works great for power.
  12. Replies
    20
    Views
    744

    I'm just not familiar with what to do with the...

    I'm just not familiar with what to do with the AEM and MPVI2. I only have an MPVI Pro. Give it a try and see what readings you get.
  13. Replies
    20
    Views
    744

    Always use the Pro HPT but these input/output...

    Always use the Pro HPT but these input/output values worked with my AEM 30-4110.
  14. Yes, under tranny TM. First gear torque limit...

    Yes, under tranny TM. First gear torque limit to 1000.
  15. Replies
    20
    Views
    744

    Try this wiring.

    Try this wiring.
  16. Do you have transmission tuning. Might need to...

    Do you have transmission tuning. Might need to bump up the first gear torque limit.
  17. Replies
    6
    Views
    357

    To correct your speedometer all you do is change...

    To correct your speedometer all you do is change the Sensor Calibration, VSS tire revs per. If your speedometer reads fast then increase revs/mile or vice versa. I use my GPS in my phone to...
  18. I don't consider myself a tuner but I did follow...

    I don't consider myself a tuner but I did follow the instructions and found it fairly easy to set up a wideband. Almost got to have one unless you have a Dodge or Ford vehicle that comes from the...
  19. Replies
    2
    Views
    112

    Thanks Bill! That fixed it!

    Thanks Bill! That fixed it!
  20. Replies
    2
    Views
    112

    New laptop not reading controls correctly

    What control do I need to change in my laptop to correct my HPT controls? Old laptop works fine.

    Here's what I'm getting with new laptop and old.
  21. Replies
    20
    Views
    744

    Dodge and Ford made this so much easier with...

    Dodge and Ford made this so much easier with factory installed wideband sensors. All you do is log the wb channel. Come on GM, get with the program!
  22. I'll give that a try. Thanks!

    I'll give that a try. Thanks!
  23. Replies
    25
    Views
    4,245

    What effect does this have on afr? Thanks Joe!

    What effect does this have on afr? Thanks Joe!
  24. Nobody has an 8 speed tranny with 600+ hp?

    Nobody has an 8 speed tranny with 600+ hp?
  25. Disable converter lockup for 1-6 gears and the...

    Disable converter lockup for 1-6 gears and the tranny will be nice and smooth. Best to leave 7 and 8 alone for best fuel mileage.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4