Search:

Type: Posts; User: Ellwein Engines

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. That was it. AC Bump spark. thanks.

    That was it. AC Bump spark. thanks.
  2. AC Bump Torque Spark? Yes the AC was running...

    AC Bump Torque Spark? Yes the AC was running during the drive data log. Have you disabled this feature and can you feel the difference?
  3. Torque Management Advance -- help me find it.

    I'm getting Torque management spark retard (advance) with an M6 Gen 3 P01 ECM car, (1994 LT1-383).
    I cannot find the code in the ECM that commands it. I have everything zero or turned off (as far...
  4. Ended up being not enough sampling resolution. ...

    Ended up being not enough sampling resolution. The MAP frequency was truncating. I put the polling at 20hz and all matches as it should. So basically a scanner operator error.
  5. screen shot

    119314 This is the best screen grab with MAP voltage and MAP kpa traced together.
  6. screen shot

    119313
  7. Car makes a bit less power because it is in a low...

    Car makes a bit less power because it is in a low kpa area of the fuel map. No actual intake elbow problem. one would think so. But anyway. The MAP voltage at WOT is perfect...4.5v as if it...
  8. Tested MAP yesterday and all tests were SAT. All...

    Tested MAP yesterday and all tests were SAT. All wiring good. MAP voltage traces perfectly with TPS (4.5v at WOT). MAP kpa still dives even though MAP voltage is 4.5V. Weird.
  9. MAP dives during WOT. Anyone else seeing this?

    I've seen this happen on numerous (3 or 4) customer vehicles in the past and just figured it was a bad Manifold Air Pressure sensor.
    Recently: No crazy combo. I have a bone stock customer LT1 with...
  10. I was thinking about something like that. Even a...

    I was thinking about something like that. Even a cell phone charger type of device. Leaning toward just tapping 5v from the TPS/AC sensor 5v. Anyone do that?
  11. What are you using for a 5v source for aftermarket pressure transducer?

    I'm hoping to log transmission pressure. What have you used as a 5v source to power your aftermarket pressure transducer?

    Thanks,
  12. Problem fixed by going direct to HPTuners web...

    Problem fixed by going direct to HPTuners web site and getting 4.2.1 scanner. Thanks. For some reason the check for new software feature does not work. Just needed to go direct to the web page...
  13. It is running well now? Good job on fixing and...

    It is running well now? Good job on fixing and thanks for the info.
  14. Got it. Thanks for keeping with this. Turns out...

    Got it. Thanks for keeping with this.
    Turns out that I did not have the latest VCM Scanner software. Corey at tech support mentioned that the check via the "Help" and then "About" does not give...
  15. Thanks for asking: I did do all of this while...

    Thanks for asking:
    I did do all of this while connected to internet, while connected to ECM, and while Pro-Link cable connected and wide band connected. I did the resync,

    I'm pretty sure my...
  16. MPVI2 does not show up in the VCM Scanner channels Selector. How to add?

    From my one week long effort to add an analog wide band to my MPVI2 (Pro) I have boiled it down to the VCM Scanner, (my version is up-to-date).
    My VCM Scanner does not show MPVI2 in the channel...
  17. No luck. I configured exactly as shown in the...

    No luck. I configured exactly as shown in the video link. I transformed. I even added a 2nd channel and assigned it to serial 2 just in case the red wire is serial 2, (as Bret at the Tuning school...
  18. Ack! Bret says Blue wire is Analog 1. The HP...

    Ack! Bret says Blue wire is Analog 1. The HP Tuners instructions say that Red is Analog 1. Anyone know which ? I have Red hooked up right now.
  19. I may not have "transformed" the channel. Like...

    I may not have "transformed" the channel. Like you I'm new to this too and spend what seems like days searching for info on this set up. I'll check that Tuning School video too. Thanks. Hope to...
  20. Any success with this ? I'm having the same...

    Any success with this ? I'm having the same problem but with an LM2. Has it been performed by anyone successfully?
  21. MPVI 2 Pro: Has anyone been able to input analog O2 via new interface?

    I've been working on this for about 10 hours. The new MPVI 2 pro. I bought the interface cable. I'm hooking up my Innovate LM2 (just one channel) analog out to the HPTuners dongle (ProLink) analog...
  22. HP Tuners: You'll save a lot of customer grief...

    HP Tuners: You'll save a lot of customer grief if you would change the licence note/warning. It needs to say, "Do not license unless you first READ the ECM and license the ECM read file" Do not...
  23. Replies
    23
    Views
    7,539

    Bill. No it doesn't.

    Bill. No it doesn't.
  24. Replies
    23
    Views
    7,539

    Info for anyone who has run into this double...

    Info for anyone who has run into this double licence trick. The help desk just flips you off. You do not provide a clear enough warning. You cannot expect a new user to know that they have to...
  25. Replies
    23
    Views
    7,539

    ok, I just got a bit of a unsat reply from...

    ok, I just got a bit of a unsat reply from support just now. Said that my ECM is for an Escilade and I am attempting to flash for a Camaro. No help what-so-ever.
    If I cannot read the ECM then...
Results 1 to 25 of 26
Page 1 of 2 1 2