Search:

Type: Posts; User: JaegerWrenching

Page 1 of 14 1 2 3 4

Search: Search took 0.00 seconds.

  1. Did it also fix the dropping too low issue as...

    Did it also fix the dropping too low issue as well?
  2. post a tune file even your stock one so i can at...

    post a tune file even your stock one so i can at least see all the tables available and not have to zoom in
  3. Btw there may be other tables at play here...

    Btw there may be other tables at play here causing a worse reaction when cold, like adding something to the control loop. I don't tune dodges But there is no doubt that going from one pump to two...
  4. It's in the PID loop control for your pressure...

    It's in the PID loop control for your pressure control valve. Usually the derivative value will need to be lowered a bit, that's the error rate of change it'll target for it's final correction. Since...
  5. Your cold start data log dops to 2700psi possibly...

    Your cold start data log dops to 2700psi possibly falling outside the minimum pressure required to actuate the injector where you hot data log doesn't. You're also making 15kpsi on startup then it...
  6. Replies
    15
    Views
    648

    Nate It's okay to have a difference of opinion...

    Nate It's okay to have a difference of opinion and have dialog back and forth on a topic you're passionate about without getting upset! If you're wanting to say a few sentences and leave thinking I...
  7. Replies
    15
    Views
    648

    I go under 18.0 all the time, unless you're going...

    I go under 18.0 all the time, unless you're going for 0 smoke production and like the stock/slow throttle response there's a descent amount to be had! Especially if timing is set appropriate for the...
  8. Replies
    15
    Views
    648

    More air means more fuel to maintain afr, which...

    More air means more fuel to maintain afr, which typically equates to more power. So yeah more power is theoretically achievable when more air is available. You're also right if you have an 80-1AFR...
  9. Heck yeah! it's a good feeling when it works as...

    Heck yeah! it's a good feeling when it works as intended right? I use my IDS or forscan every time otherwise you'll be chasing bad learned data.
  10. Replies
    15
    Views
    648

    Air is 78% nitrogen 21% oxygen and a little bit...

    Air is 78% nitrogen 21% oxygen and a little bit of other gases. Diesel engines restrict fuel amount to control engine RPM, thus they move as much air as they typically can at all times. There is a...
  11. Yes

    Yes
  12. HPtuners doesn't get all the tables cleared when...

    HPtuners doesn't get all the tables cleared when it comes to adaptives i fought that for a while before figuring it out.
  13. That file is missing shift point tables required...

    That file is missing shift point tables required to altered shift points, send in a ticket to support and ask to have them added.
  14. Replies
    11
    Views
    404

    Post the tune file

    Post the tune file
  15. Is your battery voltage good? Will it let you...

    Is your battery voltage good? Will it let you flash your stock file back into it?
  16. Replies
    14
    Views
    1,088

    You're hitting a torque limit, up your allowed...

    You're hitting a torque limit, up your allowed torque vs RPM map and atmospheric torque limit map. It happens as you add fuel because more fuel means more torque thus clipping the limit.
  17. Replies
    13
    Views
    877

    It's really how it feels, I've had one setting...

    It's really how it feels, I've had one setting work great on one truck and on another not so much.
  18. Replies
    13
    Views
    877

    Agreed i do some slow driving in parking lots and...

    Agreed i do some slow driving in parking lots and sometimes it can be a little rowdy, i keep it closer to stock in low torque areas, but when i tip in it gets it!
  19. Have you updated your PW map to match the new...

    Have you updated your PW map to match the new injector? You need to know where those injectors start flowing more vs a stock injector and also make sure your surge isn't fuel pressure related. As the...
  20. Replies
    7
    Views
    667

    Not to mention the tables are labeled...

    Not to mention the tables are labeled incorrectly, i've asked for the proper tables to be added and asked to have the max RPM be relabeled to enable to and Min RPM be relabeled to disabled because...
  21. Replies
    1
    Views
    322

    Send in a request to support asking for it to be...

    Send in a request to support asking for it to be added
  22. Sticky: What does it say when you try to?

    What does it say when you try to?
  23. Replies
    5
    Views
    596

    You select and read out only the specific...

    You select and read out only the specific controllers you want. After connecting your MPVI1 or 2 hit gather info, it will pull up all available controllers and they automatically default to be read...
  24. Clear the KAM and retest

    Clear the KAM and retest
  25. Replies
    3
    Views
    696

    That sounds like a possible ford question, you...

    That sounds like a possible ford question, you should have a gear position sensor outputting a signal from your shifter going to the PCM and then to the TCM, possibly to both simultaneously. I'd...
Results 1 to 25 of 343
Page 1 of 14 1 2 3 4