Search:

Type: Posts; User: Pwiles

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    564

    PCM controlled shift light

    I have looked at this thread
    https://forum.hptuners.com/showthread.php?28762-Adding-a-Shift-Light-to-be-Controlled-by-the-PCM-(LS1-based-PCM)-MANUAL-TRANS-ONLY!

    Is there PCM terminal on an...
  2. Can the shift light be used on an auto trans...

    Can the shift light be used on an auto trans application? If so which terminal on the PCM needs to be used.
  3. Replies
    2
    Views
    1,355

    Sorry to go off topic. What water pump are you...

    Sorry to go off topic. What water pump are you using? Are you launch on a trans brake? If so how are you controlling launch RPM?
  4. Replies
    1
    Views
    1,041

    Short powerglide VSS

    I am using a short powerglide in a rear engine dragster. I am using a 2000 Chevy Truck PCM. I would like to record output shaft speed.
    Any ideas on mounting a speed sensor. I was thinking...
  5. View Post

    I've been working on tuning my MAF and noticed that fitting a curve to the data may be a good way to refine the results from logging. I can't be the first one to think of this, so has anyone else...
  6. Replies
    4
    Views
    3,914

    What amount of wheel torque error is acceptable?

    What amount of wheel torque error is acceptable?
  7. Replies
    4
    Views
    3,914

    IPC wheel toque error

    I have been logging wheel toque. How do I correct wheel toque errors?
  8. Replies
    26
    Views
    14,320

    Yes fuel system is adequate.

    Yes fuel system is adequate.
  9. Replies
    26
    Views
    14,320

    I have raised MAF as high as it will go, and I am...

    I have raised MAF as high as it will go, and I am still lean. I need more range. Is Cylair WOT the way to get this? At what PSI is the MAP sensor toped out?
  10. Replies
    26
    Views
    14,320

    Thank you Murfie The car (CV 2011) is boosted. I...

    Thank you Murfie
    The car (CV 2011) is boosted. I can't control AFR in boost. I keep adding to the MAF table until maxed and still lean. Next I max out the cylair ( both max and WOT) went so rich it...
  11. Replies
    26
    Views
    14,320

    Any help? An old post to look at? My search just...

    Any help? An old post to look at? My search just came back to crank it up.
  12. Replies
    26
    Views
    14,320

    Cylair WOT Cylair Max

    1 When is Clyair WOT multiplier active? IE load, RPM, TP, ETC
    2 When is Clyair Max multiplier active? IE load, RPM, TP, ETC
    3 What toggles need to be enabled or disabled for these to be used?
    4...
  13. Replies
    7
    Views
    2,837

    Thank you.

    Thank you.
  14. Replies
    7
    Views
    2,837

    What is MAF period?

    What is MAF period?
  15. Replies
    1
    Views
    1,581

    6210562106 Here is a log and channel config file.

    6210562106
    Here is a log and channel config file.
  16. Replies
    1
    Views
    1,581

    commanded AFR AFR error channels HP3.2

    When Looking for AFR commanded and AFR ERR channels I can not find them. I am trying to set up an AFR error graph. The vehicle is a 2011 Crown Vic.

    Any ideas ? Can I make these channels?
Results 1 to 16 of 17