Search:

Type: Posts; User: sasdakota

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    8,975

    I had the same issue. I'm collecting data to open...

    I had the same issue. I'm collecting data to open a support ticket for it.
  2. Replies
    4
    Views
    2,940

    Post the tune.

    Post the tune.
  3. 6.0 Powerstroke FICM tune large pulse width

    What is the largest Pulse width any of you have on a log? I am seeing 2.5ms in the log with Pulse Width PID, even though I am commanding 120mm3 in the same log and the FICM tune is 3.0ms at 120mm3.
    ...
  4. Replies
    6
    Views
    2,983

    Pilot timing is based off main timing. So pilot...

    Pilot timing is based off main timing. So pilot is Main* + Pilot adv*(after factoring modifiers) = pilot timing. The min delay is a shut off, so if Pilot was set to happen too close to the main shot...
  5. Replies
    4
    Views
    4,737

    Go 70x67 turbine. I run a 67/67 currently,...

    Go 70x67 turbine.

    I run a 67/67 currently, have a 63/67 set of wheels and custom cover on its way to me. Have tuned a handful of 63/65 and 67/67 also. Tater doesn't do anything bigger than 63/67...
  6. Replies
    4
    Views
    4,737

    First off, do not go bigger than a 63mm...

    First off, do not go bigger than a 63mm compressor wheel.

    Second, Tuning.
    Use the min/max tables to drive the vanes to your desired position. Back pressure is not really a factory here, that is...
  7. Replies
    9
    Views
    6,184

    I'd be willing to bet that pilot is still firing...

    I'd be willing to bet that pilot is still firing even though you think you have it disabled. The 03's think a bit differently than later model CR.
  8. Replies
    9
    Views
    6,184

    Review your total timing (pilot+main)

    Review your total timing (pilot+main)
  9. Replies
    3
    Views
    2,142

    I believe Cummins/Chrysler do that for noise and...

    I believe Cummins/Chrysler do that for noise and emissions reduction on cold starts.
  10. Replies
    3
    Views
    1,925

    I found those also, did not at all expect it to...

    I found those also, did not at all expect it to be under torque management!?!

    Thank you for taking the time to post that. I think we are going to move forward with tuning this truck on HPT.
  11. Replies
    3
    Views
    1,925

    6.7 (2016) Support

    Are there any plans to add turbo vane tables? I have a work truck that wants us to adjust vanes a little bit for boost control and exhaust braking but I did not see anything of the sort when pulling...
  12. Replies
    2
    Views
    1,474

    ronney, The gear ratio and tire size adjustments...

    ronney, The gear ratio and tire size adjustments mapped in PCM are for logic calculations like gear rationality, etc...
  13. Replies
    3
    Views
    2,227

    Hows the modified turbo working with all the...

    Hows the modified turbo working with all the emissions equipment?
  14. Replies
    10
    Views
    6,582

    From the tables I have seen I think it is...

    From the tables I have seen I think it is feasible to have 4k fueling without weird "quirks".

    Need to talk a buddy into buying a 98.5-02 so I can tinker on it. Otherwise I am just making guesses.
  15. Replies
    10
    Views
    6,582

    Smarty UDC pro has 98.5-02 VP44 custom tuning....

    Smarty UDC pro has 98.5-02 VP44 custom tuning. Just saying.
  16. Thread: Rpm limiter

    by sasdakota
    Replies
    5
    Views
    3,503

    Stock turbo? Fuel upgrades?

    Stock turbo? Fuel upgrades?
  17. Replies
    1
    Views
    1,924

    07.5-09 68RFE Support

    Hey guys, any chance of getting the min/max turbine speed thresholds added? They are currently keeping me out of lockup in 3rd and delayed in 4th. MCC had them and it was obvious which were in the...
  18. Replies
    4
    Views
    3,061

    I would suggest calming down. Click on every tab...

    I would suggest calming down. Click on every tab in the software and ready everything on each page. Understand it or not. Know what you have and where it is. There is lots of talk about tuning...
  19. Replies
    4
    Views
    2,954

    I use autoenginuity for those types of...

    I use autoenginuity for those types of repair/maintenance/diagnostics. It has worked well for me so far.
  20. realistically, a demo file should have a flag...

    realistically, a demo file should have a flag that does not allow it to be licensed.
  21. Thread: Idle Droop

    by sasdakota
    Replies
    6
    Views
    4,386

    I didn't pack my gear with me today I'll take a...

    I didn't pack my gear with me today I'll take a look later.

    What boost are you seeing flat ground cruising at 60mph? Both towing and empty. And what is peak boost?

    Is the arduino/code able to...
  22. Thread: Idle Droop

    by sasdakota
    Replies
    6
    Views
    4,386

    Are they full injector sets or nozzles on your...

    Are they full injector sets or nozzles on your stock injectors?

    Is the "smoke" thick and dark or more like a light grey haze?

    Post up your tune I'll see if some points stick out to look for.
    ...
  23. Thread: Idle Droop

    by sasdakota
    Replies
    6
    Views
    4,386

    I would set pulse back to stock (assuming still...

    I would set pulse back to stock (assuming still factory injectors). And limit fuel by boost tables. also look at timing for that range (pilot and main or combo of both)
  24. Wish I could help, only tuned manual trucks so...

    Wish I could help, only tuned manual trucks so far with HPT...

    I could take another look if you'd like but if the other guy got it to work not sure what I can do different.
  25. So Beta was roughly 3mo ago. Any progress on a...

    So Beta was roughly 3mo ago. Any progress on a release?
Results 1 to 25 of 37
Page 1 of 2 1 2