Search:

Type: Posts; User: redyns333

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. any updates for 05???

    any updates for 05???
  2. ts an 05 i made a bench harness for it im looking...

    ts an 05 i made a bench harness for it im looking to find a pass through to try and re flash it
  3. I will post it tomorrow its definitely chooo...

    I will post it tomorrow its definitely chooo chooing now runs better than ever I got the idle leaned out using the VE table i was thinking other things adjusted the idle afr so i changed a bunch of...
  4. Replies
    3
    Views
    1,062

    ya got it to 14.8 using the VE played with some...

    ya got it to 14.8 using the VE played with some other stuff but it didnt change thank you
  5. Replies
    3
    Views
    1,062

    rich idle and dont know how to change it

    im idling in park with a warmed up motor at 11.5 afr any advise on how to get it set right ?
  6. im idling in park at 11.5 afr any idea how to...

    im idling in park at 11.5 afr any idea how to change it?
  7. So to scale my srt4 injector i downloaded a tune...

    So to scale my srt4 injector i downloaded a tune for an srt4 coped the injector data and pasted it in my hemi injector table 14 cells vs the srt4 11 cells than interpolated the last 3 cells
  8. whats your build? this thread is getting a lot of...

    whats your build? this thread is getting a lot of views not a lot of knowledge being shared i feel like hp would get more customers if the knowledge was more user friendly
  9. Im wondering because if i set my wot to 5 volts...

    Im wondering because if i set my wot to 5 volts if that will effect kick down and shifting of the trans. I like the idea of cutting out the PE table by setting the WOT to 5v and only using the VE...
  10. I disabled all the 02 sensors i never thought...

    I disabled all the 02 sensors i never thought about getting rid of PE something i might try on my next day off. i was playing with the wot delay read some stuff about how it was set really low i...
  11. how do i know im going into power enrichment? at...

    how do i know im going into power enrichment? at a certain pedal position above 47% the motor goes completely flat. im forcing open loop
  12. Replies
    4
    Views
    1,347

    get a matching skim box key and ecm from the...

    get a matching skim box key and ecm from the junkyard
  13. I am thinking about removing my o2 putting in...

    I am thinking about removing my o2 putting in wide bands and tuning using VE and PE??
  14. IM back tuning

    IM back tuning
  15. Im back in you?

    Im back in you?
  16. Replies
    11
    Views
    4,770

    so HP basically told me kick rocks tow your truck...

    so HP basically told me kick rocks tow your truck to the dealer and pay to ATTEMPT to reflash my PCM. I went to the junkyard bought a steering column with keys and the matching PCM from the same...
  17. I copied this from someone smart what do you...

    I copied this from someone smart what do you think?

    Volumetric Efficiency table X axis = Pressure ratio, Y axis = RPM
    The VE table is an airflow correction factor in %. Higher VE% = more fuel,...
  18. ok back to tuning after bricking my PCM

    ok back to tuning after bricking my PCM
  19. Replies
    91
    Views
    112,406

    get the key skim box off the column from the car...

    get the key skim box off the column from the car with the matching PCM i got a column, key and PCM from the junk yard for $150 taped the key to the skim box and plugged it in along with the matching...
  20. so HP basically told me kick rocks tow your truck...

    so HP basically told me kick rocks tow your truck to the dealer and pay to ATTEMPT to reflash my PCM. I went to the junkyard bought a steering column with keys and the matching PCM from the same...
  21. that sucks some how my PCM is failing protocol...

    that sucks some how my PCM is failing protocol when i tried to write i got a junk yard pcm now what do i do?
  22. ya im bored cant work on my truck

    ya im bored cant work on my truck
  23. whos got an idea ???? junkyard PCM and skim box...

    whos got an idea ???? junkyard PCM and skim box more credits for the new PCM??
  24. you are 100% right i know that now but i put so...

    you are 100% right i know that now but i put so much time in learning reading HP tuners the money i could give an F i have been poor poor really I am giving HP an OPPORTUNITY TO STEP UP WIN Im vested...
  25. doesnt look like it will run my transmission

    doesnt look like it will run my transmission
Results 1 to 25 of 69
Page 1 of 3 1 2 3