Search:

Type: Posts; User: IXR08

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    3,420

    Hi Shawn did u end up solving this?

    Hi Shawn did u end up solving this?
  2. Replies
    10
    Views
    2,270

    Did u make any progress with this?

    Did u make any progress with this?
  3. Replies
    1
    Views
    808

    Toyota 200 Series Landcruiser DPF

    Hi it appears HP tuners wont allow or can't provide a way to stop DPF fault from limiting engine power, just wondering if anyone has managed a work around or alternative way?

    Any exceptions for...
  4. Replies
    3
    Views
    1,618

    any update on this? now says it supported but not...

    any update on this? now says it supported but not sure which ford pcm to select from the 30 options in the drop list? Yes it can detect and read the transmision.
  5. Replies
    4
    Views
    4,835

    updates please?

    updates please?
  6. Replies
    1
    Views
    841

    Can you share were your base map or link to where...

    Can you share were your base map or link to where you found it please?
  7. Replies
    31
    Views
    14,291

    Any updates to the fix on this?

    Any updates to the fix on this?
  8. thanks for sharing, is this still the preferred...

    thanks for sharing, is this still the preferred method to keep the throttle open ? Do changing the torque coefficients work?
  9. Replies
    8
    Views
    2,159

    Are you sure its true knock? or just what the...

    Are you sure its true knock? or just what the logger is showing? try set knock sensor initial level to 160 & min level to 125 then reduce cylinder 5 to 0 degrees... I would also try swapping a plug...
  10. Replies
    8
    Views
    2,159

    Also you are only at 68% ethanol percentage so...

    Also you are only at 68% ethanol percentage so the table in picture below will only give you timing advance based on ethanol percentage so you would need 100% ethanol so to get the full 6 degrees...
  11. Replies
    8
    Views
    2,159

    Have u tried running the static table on cylinder...

    Have u tried running the static table on cylinder 5 at 0, i understand it to be sometimes problematic. Also looking at your log at approximately 1:14.009 there is no knock retard on any of the...
  12. Replies
    8
    Views
    2,159

    post tune file

    post tune file
  13. Replies
    35
    Views
    33,473

    Any progress on the 3.2 rangers yet?

    Any progress on the 3.2 rangers yet?
  14. Replies
    24
    Views
    6,782

    79416

    79416
  15. Replies
    6
    Views
    1,815

    Do you need to re-enable any of the patches in...

    Do you need to re-enable any of the patches in the OS tab? traction control etc?
  16. Replies
    6
    Views
    1,815

    So you just adjust the VE Normal (OPen & closed )...

    So you just adjust the VE Normal (OPen & closed ) tables and save the file before write? No need to generate co-effecients?
  17. Replies
    6
    Views
    1,815

    thanks for the confirmation..... looks like it...

    thanks for the confirmation..... looks like it works out to be an ideal solution to run a blended model and the ease of a VE table to tune for down low.
  18. Replies
    6
    Views
    1,815

    All good... i just read that I can still run the...

    All good... i just read that I can still run the MAF even with the 2 BAR SD upgrade... I assume i need to plug the maf in, lower the hi speed enable rpms in Dynamic air flow, and set the DTC's back...
  19. Replies
    6
    Views
    1,815

    2 BAR SD Upgrade back to Standard OS

    If I have a 2 BAR SD Upgrade and wish to go back to Standard OS, Does this mean ill need to use 2 more credits to do write entire with a stock file back over the 2 Bar SD tune that was in the car?
  20. Replies
    5
    Views
    1,890

    I agree, the main thing in Australian scene is...

    I agree, the main thing in Australian scene is the the mafless tune is more like a buzz word and seems to be a hangover from the GEN3's

    Can't beat a blended solution using SD with maf slot style...
  21. Replies
    4
    Views
    2,289

    what are the cam specs?

    what are the cam specs?
  22. Still waiting please hurry support!!!

    Still waiting please hurry support!!!
  23. Replies
    4
    Views
    1,948

    anyone?

    anyone?
  24. See Atached file, support have asked me to send...

    See Atached file, support have asked me to send vehicle log .... which ill do when i get the car back
  25. Ok so if they are like that the ZF's cant be...

    Ok so if they are like that the ZF's cant be tuned on some random models?
Results 1 to 25 of 96
Page 1 of 4 1 2 3 4