Search:

Type: Posts; User: robbyredneck

Page 1 of 15 1 2 3 4

Search: Search took 0.00 seconds.

  1. Did you sort this OP?

    Did you sort this OP?
  2. Thanks but I meant setting limits for filtering...

    Thanks but I meant setting limits for filtering out erroneous data . I think i remember now
  3. Forgive my ignorance it has been a decade since I...

    Forgive my ignorance it has been a decade since I last plugged my scanner in. I have a ctsv that is pretty rich so I have configured the maths as stated in the first post and I'm successfully...
  4. Did you try this OP?

    Did you try this OP?
  5. Replies
    15
    Views
    10,239

    Wow didn't realize the tcc lockup behavior was as...

    Wow didn't realize the tcc lockup behavior was as such. I would have totally over looked that. thanks guys
  6. Replies
    15
    Views
    10,239

    I just bought a v that has some serious trans tm...

    I just bought a v that has some serious trans tm going on and i appreciate your contribution. thanks
  7. Replies
    2
    Views
    1,802

    whoa dubb thanks from the future

    whoa dubb thanks from the future
  8. Replies
    1
    Views
    987

    cant help you with table but that mac valve needs...

    cant help you with table but that mac valve needs pulse width modulation. not sure if gm uses the bypass valve like that. you may have the ability to pulley up a ton and reduce boost only. I'll let...
  9. Replies
    7
    Views
    2,473

    where specifically is this 2-1 hjtrbo?

    where specifically is this 2-1 hjtrbo?
  10. same here. would like to look at this as i am...

    same here. would like to look at this as i am used to open source but would gladly use the stability of hptuners
  11. Replies
    22
    Views
    12,334

    I couldn't get it to work. I have a buddy of mine...

    I couldn't get it to work. I have a buddy of mine with a snap-on tool. Relearned it in 2minutes. Bye bye p0300 ,hello lockup
  12. Replies
    22
    Views
    12,334

    It appears you have to have all the readiness...

    It appears you have to have all the readiness monitors satisfied. can anyone confirm?
  13. Replies
    2
    Views
    1,509

    thanks so much . just the heads up i was looking...

    thanks so much . just the heads up i was looking for.
  14. Replies
    2
    Views
    1,509

    quick info on nnbs turbo

    I have not logged in for quite a while which should be a testimony to how amazing this forum is. I have a 2003 6.0 turbo silverado that has been so rock solid that i havent touched it in years. could...
  15. congrats that's haulin'. glad you didnt get a...

    congrats that's haulin'. glad you didnt get a felony speeding ticket while tuning
  16. Replies
    14
    Views
    5,260

    short or long 60s. pulse adder and voltage tables...

    short or long 60s. pulse adder and voltage tables look goofy too. when you switch to a return rail your flow rate delta no longer changes due to manifold pressure. it sounds like heatsoak. you can...
  17. Replies
    14
    Views
    5,260

    flow rate vs kpa should be the same # in every...

    flow rate vs kpa should be the same # in every cell (74.8). your probably heat soaking the iat. where is the maf?
  18. Replies
    7
    Views
    2,759

    is this an engine swap?

    is this an engine swap?
  19. Thread: New here

    by robbyredneck
    Replies
    2
    Views
    1,830

    word

    word
  20. couple of years late but it would be awesome

    couple of years late but it would be awesome
  21. Replies
    1
    Views
    2,236

    looks like both are 3bar but the ears are...

    looks like both are 3bar but the ears are different. whichever has best known slope and offset.
  22. kinda good news. your welcome

    kinda good news. your welcome
  23. the cobalt sensor your looking for is actually...

    the cobalt sensor your looking for is actually the bap sensor. you can check it with the scanner 2bar pid koeo it should read approx 100kpa.
    #12580698 is the part # i think
  24. Replies
    2
    Views
    1,764

    can you command lower with the scanner?

    can you command lower with the scanner?
  25. try this. be cautious. i just remembered that i...

    try this. be cautious. i just remembered that i used an ebay 2 bar map and i had to calculate slope and offset and it was goofy. also turbo is a china gt45 so small compressor. you may want to use...
Results 1 to 25 of 357
Page 1 of 15 1 2 3 4