Search:

Type: Posts; User: hachiroku

Search: Search took 0.00 seconds.

  1. i haven't had any issues when modifying or not...

    i haven't had any issues when modifying or not modifying this map. currently mine is maxed out as i was troubleshooting another limp mode fault.

    nevermind...just saw this reply.
  2. any permanently logged faults will need an...

    any permanently logged faults will need an appropriate tool to clear. STAR/DAS or other.

    to disable the fault from appearing you'll need to disable the fault and not just the MIL checkbox.
  3. Replies
    0
    Views
    49

    Help with fuel trim swings

    hey guys. i seem to be at a loss in regards to fuel trim swings. it would seem that at times, hot engine or cold engine, trims across the board will swing positive or negative. if i data logged 4...
  4. P0106 Manifold Absolute Pressure/BARO Sensor Range/Performance

    Hello,
    Besides, 4028 Range High and 4029 Range Low, which other area's affect triggering of P0106? I have updated 11335 Maximum Intake Pressure but still am seeing P0106. I am naturally aspirated...
  5. lol...i thought about it when i was updating all...

    lol...i thought about it when i was updating all those monitor centric maps. was going to do that as a last resort, but luckily the updates i've done to all maps thus far have been successful.
  6. that did it! thank you! now i can fine tune my...

    that did it! thank you! now i can fine tune my Optimum Torque and Load to Torque maps.
  7. Optimum Torque 32900 and Torque to Load 32850 Issues

    Hey Guys,
    I seem to be having issues with modification of either of the two maps, Optimum Torque 32900 and Torque to Load 32850. If I touch either of these maps I am receiving a P061B (Internal...
  8. Replies
    3
    Views
    199

    my W211 E63 has "Torque Limit Request Limiting"...

    my W211 E63 has "Torque Limit Request Limiting" as disabled as part of the factory map. had to avoid using the injector multiplier entirely as any modification from me was causing a P0607.
  9. catalytic converters can handle any amount lean...

    catalytic converters can handle any amount lean value. when you run lean EGT's go down because there isn't any fuel to burn. what damages catalytic converters is excessive fuel and ignition of...
  10. Replies
    5
    Views
    443

    yep...will try a few more things. i had the same...

    yep...will try a few more things. i had the same issue with Eurodyne Maestro for my B6 Audi A4 with Motronic ECU. i believe i had to also update not only the check box for MIL but also but set for...
  11. Replies
    29
    Views
    4,792

    on my E63, throttle hits 100% with Accelerator...

    on my E63, throttle hits 100% with Accelerator Pedal D (SAE) and Throttle position hits 87.9% with its factory settings and factory map. if anybody is having issues i'd recommend simply copying over...
  12. Replies
    5
    Views
    443

    I've switched off MIL for all sensor 2 and...

    I've switched off MIL for all sensor 2 and catalyst items, but still receive a MIL
  13. Replies
    3
    Views
    199

    i'm on my 3rd day with the product and have the...

    i'm on my 3rd day with the product and have the same exact issues you describe.
  14. i have yet to try this or lean burn for the M156,...

    i have yet to try this or lean burn for the M156, but from what I've experienced with my Audi A4 B6, the Motronic ECU has this hard coded as a safeguard for that vehicle.
  15. Replies
    24
    Views
    12,678

    Sticky: agree...1/3rd of the first post no longer matches...

    agree...1/3rd of the first post no longer matches the latest version of VCM Editor 4.4.4
  16. Replies
    1
    Views
    109

    Sticky for BETA change log?

    Hello,
    Wanted to ask if there was a sticky for the beta software change log? I want to make sure that if there is no need for me to use the beta, meaning no features for me, that i won't use it.
    ...
  17. Replies
    76
    Views
    24,128

    Sticky: PWM? I believe the expander hub can accept this...

    PWM? I believe the expander hub can accept this type of signal.
  18. Replies
    76
    Views
    24,128

    Sticky: best answer i've ever heard of any company...

    best answer i've ever heard of any company offering an engine management solution. will be purchasing within the next few months to ditch my canned tune. the next question...could that be utilized...
  19. Replies
    76
    Views
    24,128

    Sticky: not sure if this has been asked before...can flex...

    not sure if this has been asked before...can flex fuel sensor data be utilized with the new inputs as part of the prolink or expander hub for a vehicle that did not come with flexfuel from the...
Results 1 to 19 of 19