Search:

I have a l92 out of a 07 GMC Yukon Denali with the E38 ECU. I have install a 4L60E 17 Pin connector with a TCM-42. I need to know if they are compatible and what if not what am I going to need to...

Thanks, I get a V8 e38.

I copied my tune off of my E38 escalade to a friend of mine E38 ECU which was from an impala v6 so he could get his crate ls3 motor running for tuner. after coping the tune I ran my motor on the v6...

OK first of all thanks to all of your for you help. I finely finish hooking all the sensor up on the truck and fired it up. It idle and ran great in fact the best it has every ran. Took it for a long...

OK, I finely done what I should have done a week ago and pull the harness out. Keep in mine that was a new harness when this project started and not much to my surprise here is what I found. All the...

87722I put in the new 28lbs injectors, new plugs, new o2 sensors, and still no o2 and the thing ran worst than before. I downloaded a stock tune and will go from there. I have just finish with the...

Thanks, I now see it is just not as simple as saying all 36LBS are the same, which I now see they are not. I see, I am going to have to put a lot more time end on this subject to get my head wrap...

OK, I finely got the new O2's and 28LBS injector in. I am installing them and new plugs tomorrow and will update everyone when I finish. Thanks Norm

I am sorry I did answer your question. Mostly 99 to 07 Chevy and GMC truck with 0411 PCM. Thanks Norm

I am asking this question in general. It has to get it from the PCM, but I have seen no place to enter injector size in the PCM that I have looked at. The only place that I seen injector info is in...

Newbie here and maybe I have not looked enough but, how does the scanner come up with the injector size? Thanks Norm

OK I think that I have the issue fix with O2's. I was watching a you tube video on how to test your O2 and the guy said that if you have .5 volts on you post O2's they are reading correctly. WOW that...

I am trouble shooting the o2 sensor out of the truck and I am missing something. A is tan to blue 29 should be grounded to the case and B is purple to blue 69 (data) C is ground and D is 12V. I have...

I will try that after I get the new injector and plugs end. Thanks Norm

That the same diagram I was using to trouble shoot the circuit and everything was where it was suppose to be. The only thing you can't check is the voltage from the purple wire from the PCM and I...

the o2 are ones for a 98 -02 vortex truck (AC-DELCO AFS 98). They are a 4 wire and the LH side, pin A is tan to Blue 29(and it has a ground to case of o2), pin B is purple to blue 69, pin c is ground...

my question is 22 lbs. enough for this motor with a cam and better exhaust?

I pull the injector rails and there are two type of injectors on the motor. First one is 25323974 (21.7LBS) and the second one is 25317628 (22 LBS). I am going to run the motor and use the new set of...

you are so right. I am on my way to pull a injector to see what they are and go from there. I am also looking to change the intake to a ls1/2 OEM type. and go from there. Thanks for the help Norm

I just checked the David ECM and it is for 02 5.3 1500 Silverado 4 wheel DR 4 speed over drive. This is the tune that I would like to use because the other PCM has been tuned by the guy that left...

I just checked the Eugene PCM and it is a 2000 Silverado c2500 6.0 most likely a 4l80. I will let you know on the other one and the ejectors later today. Thanks Norm

I am sure it is a 5.3 the PCM for both is a 0411 the 89 one is a 02 pcm and the other one is 01 Chevy truck 0411. the harness is a PSI 1092 and it is a blue/red. The intake is a PROCOMP china one...

Thanks, I have the year and model on both the pcm that I used and I will get them. I do know that the motor was overhaul and a cam was put in it, but don't know what it is. Thanks Norm

First I am a newbie and should not be this far into this issue that I am, but here I go. We had a local tuner guy up here that walk away and left a lot of people that I had send to him in a mess....