Search:

Type: Posts; User: JFiorito

Page 1 of 2 1 2

Search: Search took 0.00 seconds; generated 23 minute(s) ago.

  1. Replies
    8
    Views
    2,073

    Full log from that post^^^ 102734

    Full log from that post^^^


    102734
  2. Replies
    8
    Views
    2,073

    Well I spoke too soon... It popped up again under...

    Well I spoke too soon... It popped up again under a slightly different scenario this time. I was just doing a pull from a stop light and in first gear I had hit Spark Source - Cylinder Pressure limit...
  3. Replies
    8
    Views
    2,073

    So far so good on turning off gearbox limit. Only...

    So far so good on turning off gearbox limit. Only have 1 drive on it so far though. Fingers crossed. I ended up using the Bowler Transmissions bluetooth signal converter so I didn't change the VSS in...
  4. Replies
    8
    Views
    2,073

    Log was too large to upload. Here a snippet from...

    Log was too large to upload. Here a snippet from a shorter one with knock and the full log:

    102293

    102294
  5. Replies
    8
    Views
    2,073

    T56 Swap Tune Issues

    Hey guys,

    I just finished a T56 Magnum XL swap on my 2.3L Roushcharged '16 GT. Ever since then I've had (more) issues with torque control and I've also had some knock show up. I've always had some...
  6. Replies
    6
    Views
    3,790

    So I finally got the swap finished (also...

    So I finally got the swap finished (also installed exhaust dumps, killer), I ended up using the bowler wiring kit to fix the speedometer, but I ran into some other tune issues. I had some minor...
  7. Replies
    6
    Views
    3,790

    Ah alright I did read that as well. I got one of...

    Ah alright I did read that as well. I got one of those signal converters with the kit, but not sure if I'm going to use that or just change it in the tune.
  8. Replies
    6
    Views
    3,790

    Oh and I am aware of the speedo change

    Oh and I am aware of the speedo change
  9. Replies
    6
    Views
    3,790

    S550 T56 Magnum XL Swap

    Hey guys,

    I'm installing a T56 swap kit on my '16 supercharged GT (MT-82 finally gave out in spectacular fashion) and I was wondering if there was anything special I needed to change other than...
  10. Replies
    33
    Views
    14,253

    Hm I'll keep that in mind. I would prefer to get...

    Hm I'll keep that in mind. I would prefer to get the existing system figured out, but will definitely keep that in mind. Everything points to the torque tables being the source of my issues, but...
  11. Replies
    33
    Views
    14,253

    I have had the same experience as you. I bought...

    I have had the same experience as you. I bought the tuning school coyote tuning book and was disappointed. I'm curious to see how the new book looks... The recipe seems like it would work alright for...
  12. Replies
    27
    Views
    8,256

    Alright that makes sense. So I've been getting my...

    Alright that makes sense. So I've been getting my ass kicked by this issue for a long time now. I feel like I've tried adjusting everything by now. Only thing I haven't messed around with much is the...
  13. Replies
    27
    Views
    8,256

    Alright I guess my concern is that I have to...

    Alright I guess my concern is that I have to change a number in the window to get it to calculate the inverse even if I've already changed the Torque tables before opening up the inverse calculator....
  14. Replies
    27
    Views
    8,256

    Alright so I've been taking a look at my desired...

    Alright so I've been taking a look at my desired airmass vs my current airmass. I can see that depart from each other when I start having Torque Control kick in. I also noticed that at WOT they...
  15. Replies
    27
    Views
    8,256

    Alright I have not made any progress so far...

    Alright I have not made any progress so far adjusting the Driver Demand tables. Maybe I'll go back and make some fine adjustments to the Torque tables. I was shocked a difference in 3 ft-lb would...
  16. Replies
    27
    Views
    8,256

    Alright so the dots are slowly connecting. It...

    Alright so the dots are slowly connecting. It seems like adjusting the TRQ tables will adjust the Scheduled TRQ. Now after looking at the logs (for the millionth time) I think I've noticed a pattern....
  17. Replies
    27
    Views
    8,256

    Hopefully we're on to something as I have no...

    Hopefully we're on to something as I have no issues in 6th gear. I increased my Driver Demand tables by 10ft-lb at the lower pedal/RPM areas. Will report back tomorrow
  18. Replies
    11
    Views
    2,769

    I would double check your Max Knock Retard Limit....

    I would double check your Max Knock Retard Limit. I've heard of people changing this to 0 degrees... scary

    98944
  19. Replies
    27
    Views
    8,256

    Thank you that was a good explanation, but I have...

    Thank you that was a good explanation, but I have a few more questions for you. For starters, which torque would you reference to adjust your TRQ tables? Scheduled TRQ? I went from a 79mm upper...
  20. Replies
    27
    Views
    8,256

    Also, where do the Driver Demand Tables come in...

    Also, where do the Driver Demand Tables come in to the equation? I feel like those should have been adjusted when I went to the smalley pulley, but they are the same
  21. Replies
    27
    Views
    8,256

    Alright so I started logging my MAF vs Desired...

    Alright so I started logging my MAF vs Desired MAF and it definitely varies quite a bit in certain areas. So my question is, how do the TRQ/Inverse tables affect the MAF? I lowered my TRQ tables by...
  22. Replies
    7
    Views
    3,406

    Exactly I'm not sure. It seems too simple to just...

    Exactly I'm not sure. It seems too simple to just copy and paste that to me. I would guess that adjusting the table would affect how these turn out. If it just knew the transport delays then why...
  23. Replies
    7
    Views
    3,406

    I'm using "O2 Transport Delay Total" 98799

    I'm using "O2 Transport Delay Total"

    98799
  24. Replies
    7
    Views
    3,406

    Transport Delays

    Hey guys,

    I recently discovered that you can log your O2 transport delay. I have 1 7/8" catted LTH and am currently failing my Catalyst, O2 Sensor, and Heated O2 Sensor readiness checks (If I turn...
  25. Replies
    17
    Views
    4,756

    Maybe it's your Fuel Enrichment Pedal? I've been...

    Maybe it's your Fuel Enrichment Pedal? I've been tinkering with this lately because I'd be stuck in stoich longer than I wanted when rolling into the throttle causing some knock.

    98768
Results 1 to 25 of 50
Page 1 of 2 1 2