Search:

Type: Posts; User: gapd you

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    787

    lower timing in the low rpm range and make sure...

    lower timing in the low rpm range and make sure fuel is dead on for both vve and maf should clean it up a lot.
  2. Replies
    1
    Views
    973

    idle issues file and log attached

    having an idle issue with 08 vette with ls3, vortech v3, btr3 cam, fore tripple pump, id1050 injectors, headers, e85.

    ive tried big mikes gen v guide as well as playing with base running air flow,...
  3. Replies
    0
    Views
    778

    Another LS3 Surging Thread

    Been having a hard time getting rid of the surging between 1200 and 1800 rpm. looking for any advice. Ive lower'd timing and it still seems the same i've also been playing with injector boundry
    ...
  4. Replies
    2
    Views
    1,836

    This worked! Needed around with some torque mgmt...

    This worked! Needed around with some torque mgmt settings and set P0101 to no error reported. Not sure which one did it but I can now start in first gear!
  5. Replies
    2
    Views
    1,836

    Limp mode when ve tuning. Stuck in 4th!

    95886
    95887

    08 ls3 vette with 6l90 is wanting to takeoff from 4th gear when tuning ve. I have attached the file and log if anyone sees anything to help me out with this problem.


    Thanks!
  6. Replies
    13
    Views
    3,702

    Got the fuel looking better on the maf curve with...

    Got the fuel looking better on the maf curve with the first revision and the shifts while cruising are night and day difference!

    Next i need to figure out what to adjust to keep the rpms from...
  7. Replies
    13
    Views
    3,702

    took the car out for a short log on the original...

    took the car out for a short log on the original tune today still with no wideband installed yet. maf curve looked a little lean. I'm going to richen it up some and make the other adjustments to the...
  8. Replies
    13
    Views
    3,702

    I don?t plan to change PE until I get the...

    I don?t plan to change PE until I get the wideband installed in the next few days. I will probably log some drivability stuff today to check fuel trims and the part throttle bogging when shifting.
  9. Replies
    13
    Views
    3,702

    I do not want to be rebuilding the trans. It is...

    I do not want to be rebuilding the trans. It is still a stock trans in the car. Will 40% be good?
  10. Replies
    13
    Views
    3,702

    What would be the best approach to dial in the...

    What would be the best approach to dial in the torque management? Im still trying to learn the 6l90. Thanks for the recommendations.
  11. Replies
    13
    Views
    3,702

    Thank you for the detailed description on each...

    Thank you for the detailed description on each subject Robzl1. This helps me out so much. I will work on the suggested areas and hope for some improvement.

    If I half ivt will it throw a bunch of...
  12. Replies
    13
    Views
    3,702

    08 Supercharged Corvette Tune Advice

    Just picked up an 08 vette with A&A V3 with 3.4 pulley, btr3, fore fuel, id1000, headers, yank 3400, meth,dsx flex fuel. The previous owner ran best of 9.67 at 143 mph so the car seems good on the...
  13. Replies
    2
    Views
    1,060

    Thanks for the help ill play with it. It seems...

    Thanks for the help ill play with it. It seems these cars like to snap intermediate shafts in the trans so i hope i can get it smoothed out.
  14. Replies
    2
    Views
    1,060

    09 CTS-V 4 to 5 shift hard

    Can anyone have a look at the log and file and help me out with the 4 to 5 shift. everything else is smooth. thanks in advance
  15. Replies
    2
    Views
    1,524

    Tune is likely maf only. I’ve had similar issues...

    Tune is likely maf only. I’ve had similar issues with an intake. Tune your vve table and then run blended up to 2500 rpm or so and it will drive a lot better.
  16. Replies
    12
    Views
    2,377

    catch can routing is wrong. see mighty mouse...

    catch can routing is wrong. see mighty mouse website for correct routing. this could be a cause of your issue.
  17. Replies
    3
    Views
    1,258

    Solved the issue. I accidently flip flopped the 2...

    Solved the issue. I accidently flip flopped the 2 sensors on the lid when i got it back from powdercoat. Make sure the red map goes toward the firewall!!!!!!!:banghead:
  18. Replies
    3
    Views
    1,258

    Ill post the log in the morning when i get back...

    Ill post the log in the morning when i get back on my laptop. Unfortunately the map sensor is showing 140+ kpa lol. Hoping its just a bad sensor. I had to increase idle airflow and startup airflow...
  19. Replies
    3
    Views
    1,258

    Cts-v idle issue after ported blower

    Let me start by saying that I am not a tuner. I am a beginner and i?m just trying to figure out if i have an issue after i installed the blower and started the car to check for any leaks. The car has...
  20. Easiest way to do it is just disconnect the...

    Easiest way to do it is just disconnect the connector of the battery terminal. Unclip the connector on the positive terminal and leave it off. Or forscan like wveryone else said free program and $20...
  21. Replies
    1
    Views
    1,066

    Anyone Tuning 2018 f150 2.7?s

    I already have a mpvi2 for my cts-v looking to see if anyone on here tunes the f150s. Id rather buy the credits for $200 instead of buying a handheld with canned tunes.

    Im pretty familiar with...
  22. 09 cts-v trans turbine rpm is crazy high?

    Can this cause any issues? Noticed it and not sure if its a sensor or if its something in the file. Not to sure on where to start.

    83572
Results 1 to 22 of 22