Search:

Type: Posts; User: ltcbm

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    9,046

    Has there been any plans made for this ?

    Has there been any plans made for this ?
  2. Replies
    0
    Views
    499

    2021 Power wagon 6.4 ecm

    I was going to order a new ecm for this truck. 2021 5.7 is all that is listed in the drop down. Do the 6.4 and 5.7 use the same ECM?
  3. Replies
    3
    Views
    910

    Surely someone knows this

    Surely someone knows this
  4. Replies
    3
    Views
    910

    2020 ram Speedo calibration

    With the new 2019 ram hemi is there a way to adjust speedo? When you go to gear tire adjustment in the scanner it says not supported. The old body style I have been able to adjust but can not this...
  5. Replies
    3
    Views
    9,046

    Twin turbo stinger or g70 support

    Is anything coming down the pipeline for the 3.3 turbo Kia stinger or genesis g70? I know there are some interface modules that really see a boost in hp and tq. Just haven?t seen any custom tuning...
  6. Replies
    28
    Views
    17,771

    I have a 03 that i'm running a 6.7 in. It runs...

    I have a 03 that i'm running a 6.7 in. It runs great. The only issue I have is throttle sensitivity. Even when I pull a lot of fuel and time out. Turbo spools too fast. i attached it here for you to...
  7. Replies
    12
    Views
    6,060

    freakotec Is the scanner function working when...

    freakotec
    Is the scanner function working when you are hooked to the truck? the interface may not be seeing the ecm. I have done several of these and I have never had an issue with it. Editor will...
  8. Replies
    2
    Views
    1,651

    I dont know if you solved this issue yet. I just...

    I dont know if you solved this issue yet. I just notice your post. I looked at you tcm cal and made a few changes. You might try this and see if it suits you. I set these trans up like this all the...
  9. Replies
    11
    Views
    7,841

    jim I downloaded the smarty software but it will...

    jim
    I downloaded the smarty software but it will not let me open your file in demo mode. If you could take a screen shot or two it would help. Thanks
  10. Thread: 03 Ecuador swap

    by ltcbm
    Replies
    0
    Views
    926

    03 Ecuador swap

    I have an 03 here that the ecu went bad. I have another one that show to be an 04. It works on the truck but a few things such as temp gauge does not work. I tried to flash the org os in it with my...
  11. Replies
    11
    Views
    7,841

    thanks. i'll check it out

    thanks. i'll check it out
  12. Replies
    11
    Views
    7,841

    03 5.9 t0 6.7 swap

    Has anyone here done a cummins swap like this? I have a customer that has just finished this swap and has it running. He still needs it tuned. I know he has added a big stick cam. Not sure what turbo...
  13. Thread: 07 tbss

    by ltcbm
    Replies
    2
    Views
    1,759

    this one is not stk. It has a few tweaks. I have...

    this one is not stk. It has a few tweaks. I have a few 06's but the 06 uses a e40 ecm where the 07 has a e67.8003180033
  14. Thread: 2008 truck file

    by ltcbm
    Replies
    0
    Views
    660

    2008 truck file

    does anyone here have a stock read from a 2008 chevy truck with 4.3L (e37). The repository is still down and I couldnt find one online. I have a ton of e38 reads but no 4.3L ones.
    Thanks
  15. Replies
    2
    Views
    1,329

    send me your email. i have one on file for a ls3....

    send me your email. i have one on file for a ls3. once os is changed you can make changes to set for what ever engine you have
  16. Replies
    1
    Views
    945

    Any ideas?

    Any ideas?
  17. Replies
    1
    Views
    945

    vss count change on t42

    I have put a 2010 5.3 and 4l60(e38 and t42) in a 85 truck that had a 700. so i used the same transfer case which has a cable speedo. On the earlier pcms I could change the vss count from 40 to 8 and...
  18. Replies
    4
    Views
    3,810

    I did not put a resistor inline the can wires. Do...

    I did not put a resistor inline the can wires. Do you remember what size I need
  19. Replies
    4
    Views
    3,810

    help getting bench harness to work

    I have built a bench harness for a spanish oak controller from a 07 police interceptor. I can not get it to read or scam with any tool. I have the three 12v+ wires on controller wired up (pin 35. 36....
  20. Sticky: Thanks Chris

    Thanks Chris
  21. Replies
    1
    Views
    1,975

    8 speed tcc schedule

    Does anyone really understand the tcc schedule on the 8 speed. I pretty much understand the rest of it. Shift timing , pressure and firmness is pretty simple. The tcc is staying locked on decel when...
  22. Sticky: trans shifts now as it should, quick and firm....

    trans shifts now as it should, quick and firm. Thanks a bunch. the only issue I've had is an increase in the downshift bump on decal. I imagine it's in the TM. I just need to sit down and work...
  23. Replies
    7
    Views
    4,286

    shift time needs to be lowered also and torque...

    shift time needs to be lowered also and torque management. these trans finally shift as they should. quick and firm.
  24. Replies
    0
    Views
    834

    Speed and cruise control

    Don't know if anyone has run into this at least I didn't see anything while searching. I tuned a 15 gmc truck with 6.2 and a8. If I change the speed limiter from gmlan to calibration the cruise stops...
  25. Replies
    3
    Views
    2,190

    o2 voltage not swinging bank 1

    basics: I have a 2009 e67 running ls2 setup similar to a ctsv or tbss. Bank 2 o2 readings are good. Bank one stays between 430 and 460. Even if I unplug it. I checked wiring all the way back to the...
Results 1 to 25 of 91
Page 1 of 4 1 2 3 4