Search:

Type: Posts; User: nicks1031

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. 187 has a 15 degree C Type (Cone) spray pattern,...

    187 has a 15 degree C Type (Cone) spray pattern, 10 degree gamma (spray angle from centerline), at a delta of 270 degree. So it will spray to the left of plug, looking at it from the bottom up as in...
  2. Looking for 13/14 M6 Roush Stock Calibration

    Just looking to find an OE calibration to make a base file for a TVS car.
  3. Replies
    18
    Views
    2,225

    Sizing appropriately for your power goals is the...

    Sizing appropriately for your power goals is the way to go. Idle quality can suffer greatly from an injector that is too large. Here is a visual example.

    Take this 52lb injector. Black horizontal...
  4. This may not be the case here, but I have seen...

    This may not be the case here, but I have seen instances where with the Flex Fuel logic disabled, it will still reference the FFV Wot Lambda table, so just as a precaution copy over your non FFV Wot...
  5. Replies
    2
    Views
    522

    Fuel Injector Clinic or ID only IMO

    Fuel Injector Clinic or ID only IMO
  6. Pre 2011 vehicles do not have a digital MAF...

    Pre 2011 vehicles do not have a digital MAF sensor, and thus use the Airflow vs Voltage table for MAF calibration.
  7. Replies
    8
    Views
    1,777

    The 187 can go to about 0.35 ms before reaching...

    The 187 can go to about 0.35 ms before reaching the "bump".
  8. I don't think the data is the issue. Try setting...

    I don't think the data is the issue. Try setting your inferred rail pressure low table back to stock , it is set to 51 psi which will cause the ECU to request more fuel under low fuel flow conditions...
  9. Factory fuel system on this car?

    Factory fuel system on this car?
  10. Is the vehicle equipped with a return style fuel...

    Is the vehicle equipped with a return style fuel system , boost referenced regulator?
  11. Replies
    6
    Views
    1,931

    Try widening the min/max values of the gear...

    Try widening the min/max values of the gear ratios. +/- 0.05 Gave me back cruise control.
  12. Thread: First timer

    by nicks1031
    Replies
    2
    Views
    897

    Injector and MAF data was off. 118026

    Injector and MAF data was off.

    118026
  13. Replies
    5
    Views
    1,135

    You can run 1000s NA with no issue. Pump gas or...

    You can run 1000s NA with no issue. Pump gas or E85.
  14. Replies
    5
    Views
    1,135

    Save yourself time/money and just get injectors...

    Save yourself time/money and just get injectors with proven data.
  15. Replies
    16
    Views
    4,524

    You have to be a little bit careful when...

    You have to be a little bit careful when adjusting injector data. Adjusting offset, low slope, or breakpoint can have major fueling changes at low pulse widths. As well, these values are all...
  16. When switching injectors, you have to edit more...

    When switching injectors, you have to edit more than just the flow rate. You'll need to know the voltage offset values and short pulse width adders values as well. This info should be provided with...
  17. Replies
    3
    Views
    827

    Its slightly modified from the HP Tuners tab...

    Its slightly modified from the HP Tuners tab because that tab is based at 50 PSI.
  18. Replies
    3
    Views
    827

    I have some data for 50 PSI base pressure, if...

    I have some data for 50 PSI base pressure, if you'd like to give that a try. Fuel trims were within 2% on an NA car running E85 on a return style system.

    109684
  19. Where did you get the injectors from?

    Where did you get the injectors from?
  20. Fuel Trim are way off which is gonna throw MAF...

    Fuel Trim are way off which is gonna throw MAF and Load way off.
    -Injector Data is way wrong for ID1300s.
    -Stoich is set to 9.4 which would be 93 % ethanol, and I assume its not that sweet if its...
  21. The units can be changed by clicking the green...

    The units can be changed by clicking the green unit label next to the entry field and it will automatically convert the value that is entered. I didn't change it to kg on my end but you can click the...
  22. You still have 2 cells incorrect. 106766 ...

    You still have 2 cells incorrect.
    106766

    Breakpoint value is also incorrect.

    106767

    Here is your file with the offset table and breakpoint corrected.
  23. My point being you entered the data values in the...

    My point being you entered the data values in the wrong units. Change the units to milliseconds and enter the values as per the data sheet.

    106762

    106763
  24. Looks like you entered voltage offset values in...

    Looks like you entered voltage offset values in micro seconds, but with the unit set to milliseconds. This makes the ECU open the injectors far longer than they need to, creating your extreme rich...
  25. Replies
    6
    Views
    2,536

    As long as the data is from a reputable injector...

    As long as the data is from a reputable injector company, I would just plug it in and go. There are a lot of tables in OEM computers that will never see full range of use. Best to not get too caught...
Results 1 to 25 of 111
Page 1 of 5 1 2 3 4