Search:

Type: Posts; User: 32vape

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Cranking eq ratio alcohol table needs adjusting....

    Cranking eq ratio alcohol table needs adjusting. Try adding 10%.
  2. Replies
    31
    Views
    950

    Does winOLS have definitions for e92 ecu's, or...

    Does winOLS have definitions for e92 ecu's, or you just have to be able to define tables yourself out of the hex?
  3. Replies
    31
    Views
    950

    What are you using to view maps not accessible...

    What are you using to view maps not accessible with hpt?
  4. Have you tried lowering the driver demand table...

    Have you tried lowering the driver demand table in the 0% row?
  5. I've had the same issue with the Lingenfelter...

    I've had the same issue with the Lingenfelter units. Dial in the car, runs great, issues. Swap injectors and pump using their data and car will hardly start. Fuel trims at 30% at idle and -20% light...
  6. Replies
    0
    Views
    217

    Reading .bin files

    I am interested in learning how to use the user defined parameters service. Wondering how a .bin file is obtained to view in tuner pro? Is there a go to obd2 reader for this? I do mostly GM e38, e67,...
  7. Replies
    1
    Views
    444

    OBD 2 tool for reading .bin files

    Anyone have a recommendation for an obd 2 tool for reading .bin files to view with tuner pro? Specifically for e38, e67, e92 GM ecu's.
  8. Replies
    9
    Views
    796

    How are you checking the fluid?

    How are you checking the fluid?
  9. My 1le does the same thing. If you log immediate...

    My 1le does the same thing. If you log immediate torque source, you'll see it oscillate between none and axle. While in axle control the timing drops significantly. If you lower the vtt in the cruise...
  10. Replies
    8
    Views
    636

    What's you injector pulsewidth? Anything over...

    What's you injector pulsewidth? Anything over 5.6-5.7 is too much.
  11. Replies
    27
    Views
    2,427

    You need to go back to your stock file and start...

    You need to go back to your stock file and start over. Hook your pcv system back up like factory. There is absolutely no need to touch the vve or vtt to start out tuning for a bolt on setup like...
  12. Replies
    10
    Views
    621

    Some of the trucks already have the wiring in...

    Some of the trucks already have the wiring in place for a flex sensor. The connector is down on the driver frame rail in front of the fuel tank.
  13. Replies
    6
    Views
    438

    If you get a pro link cable from hp tuners you...

    If you get a pro link cable from hp tuners you can input a wideband into the mpvi 2. You will need to at least remove the catalytic converters to see some power gain, especially if you have poor fuel...
  14. Replies
    6
    Views
    438

    With poor quality fuel, there will be no power...

    With poor quality fuel, there will be no power gain from tuning. You will need to drive the car on the road or a dyno and be able to perform heavy acceleration with a wideband air/fuel gauge to see...
  15. Replies
    28
    Views
    5,411

    Crossing forum sections, but have any of you...

    Crossing forum sections, but have any of you guy's run into this on a gen V di platform? Having this same issue on my heads, cam, headers, no-cats 17' SS 1LE. After a DFCO decel when the injectors...
  16. Replies
    3
    Views
    526

    I wish we had answers for this. Lots of customers...

    I wish we had answers for this. Lots of customers waiting. Probably have to wait for c8 ecu access first.
  17. What is the exhaust setup on the car?

    What is the exhaust setup on the car?
  18. It might be worth a shot with a 2010 Z06 file....

    It might be worth a shot with a 2010 Z06 file. You might just better off just going through the normal motions of e38 tuning with the Camaro calibration though. If you're using the ls7 injectors that...
  19. Replies
    7
    Views
    593

    So the solenoid is normally energized below 6000...

    So the solenoid is normally energized below 6000 rpm. Above that it's released and the oil pump moves to the high pressure setting. I jumped the wire the ecu grounds to a permanent ground to hold it...
  20. Replies
    4
    Views
    240

    So, 2017 ZL1 A10? 101197

    So, 2017 ZL1 A10?

    101197
  21. Replies
    7
    Views
    593

    That's typically what I see. We rebuilt the...

    That's typically what I see. We rebuilt the engine on this one. New GM oil pump, bearings, rings, Johnson 2110 lifters, deleted vvt, deleted dod, cam, Manley LT4 spring kit, Trend pushrods .060"...
  22. Replies
    7
    Views
    593

    Anyone?

    Anyone?
  23. Replies
    7
    Views
    593

    ZL1 LT4 oil pressure log

    Anyone have a log showing oil pressure at 6500 rpm on a ZL1 LT4? Doesn't matter on mods or tuning. Just need to see oil pressure. I am seeing a spike in oil pressure from 65 psi to 85 psi starting at...
  24. Replies
    7
    Views
    609

    It's either really heat soaked or the intercooler...

    It's either really heat soaked or the intercooler coolant is not cycling. It's not going to make good power with 150+ manifold air temps. Recheck there is no air in the intercooler system and the...
  25. WE NEED THE T93 UNLOCKED! Please and thank you.

    WE NEED THE T93 UNLOCKED! Please and thank you.
Results 1 to 25 of 112
Page 1 of 5 1 2 3 4