Search:

Type: Posts; User: Hemi2slow

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    790

    TIre height calibration on XD Diesel

    Ok guys, so I know that the XD diesels are not supported for tuning (which I would hope that it would eventually happen, because the available platforms are a PITA), but what about speedo...
  2. Replies
    0
    Views
    1,288

    Segment swap ? on custom OS

    If I need a segment swap done on a car with a 2 bar OS, do I need to send the stock file from the car to support along with the donor 4l80 file and then convert the file back to 2 bar once the swap...
  3. Replies
    11
    Views
    5,308

    4l80 segment swap question

    Ok guys, I've searched through the trans section and I haven't seen the answer I need. Sorry if this has been asked a hundred times but I can't find it.

    Do I need to do a segment swap to...
  4. Replies
    48
    Views
    36,744

    I don't mean to hijack here either, but for VVT,...

    I don't mean to hijack here either, but for VVT, as I understand it the Bluecat program doesn't take the VVT constant tables into account. But can you just adjust your VVT where you want it, and...
  5. Replies
    15
    Views
    12,572

    I have a 98 pcm and I can say that, aside from...

    I have a 98 pcm and I can say that, aside from taking a little longer to tune due to two VE tables, its not hard to tune. Just remember, tune the primary VE table using the afr error histogram, then...
  6. Replies
    9
    Views
    11,448

    Well that's what I was thinking too. From what I...

    Well that's what I was thinking too. From what I could find, the guys in the sticky seem to like doing it with the virtual VE in leau of a custom OS. I was just getting conflicting info from my...
  7. Replies
    9
    Views
    11,448

    Virtual VE tuning, to do or not to do?

    Ok so I read all the stickies on it and I have downloaded the virtual VE generator and I understand how it all works. I haven't had a chance to use it yet on a vehicle but it may be around the...
  8. Replies
    8
    Views
    3,682

    It has a 24 tooth reluctor wheel and a stock ls1...

    It has a 24 tooth reluctor wheel and a stock ls1 crank sensor. I'm not sure about the cam gear.
  9. Replies
    8
    Views
    3,682

    Gonna try and get a tune and scan file posted...

    Gonna try and get a tune and scan file posted this evening. We had thought that it might be fuel pump starving but its not a gradual loss of power like you'd expect. Its an instantaneous shut off. ...
  10. Replies
    8
    Views
    3,682

    416 won't pull past 5800

    My friend has a 2000 TA with an LS3 stroked to a 416 in it. We're running the car with the 2000 computer. Car has ported L92 heads, custom cam and is on approximately 11.3 compression. The VE...
  11. Replies
    8
    Views
    7,181

    Well I'm currently in the process of testing it. ...

    Well I'm currently in the process of testing it. I can say this, the fuel gauge isn't moving as fast now. Not sure if that is a good or bad thing. Main thing I'm worried about is making sure that...
  12. Replies
    8
    Views
    7,181

    Fuel gauge output scaling question

    Has anyone ever messed with the fuel gauge output on their vehicles? I have always been aggravated by the fact that the fuel gauge in my 04 truck doesn't read linearily. It stays on full for a...
  13. Replies
    713
    Views
    542,277

    Sticky: Picayune, Mississippi

    Picayune, Mississippi
Results 1 to 13 of 13