Help me understand the desired slip tables for the trans-torque converter-general-tcc desired slip? In 6th gear the lowest value is 20. Why would you want the TCC to slip at cruising speed?
Type: Posts; User: kevmo777
Help me understand the desired slip tables for the trans-torque converter-general-tcc desired slip? In 6th gear the lowest value is 20. Why would you want the TCC to slip at cruising speed?
Why can't I find the channel for pilot timing in the scan tool?
I cannot find the scan channel for the pilot injection timing. I can find for the pulse width and quantity, but not the timing. Did 2003 have pilot injection?? All the tables in editor are...
I expierenced the same problem w/ my ls-6 and found that I needed to disable the COT protection while tuning. This fixed my problem.
When I start my car, it seems to 'rev' up to 1500 rpm upon starting-with my foot off the gas pedal and then settle down to idle (850). What do I need to tune for the car just to start and come up to...
Is that the reason that why I'm not getting the results I'm looking for? Do I need to be concerned about hurting my cats? I'm running high flow cats, w/ my rear o2 still enabled, that is why I...
Where can I find that supplement? Thanks.
This is the document I was using "Tuning the Right Way" by Bob Morrale. See attachment for pages explaining pe tuning.
I'm understanding the proper way to tune using maf/ve tables, but could...
So then, if I set my table to read afr of 13:1 and I'm reading 12:1, do I adjust my ve table and maf at the same time or seperate (like the fuel trims)? This case I would subtract from the ve table...
I'm satisfied with my ve table, maf table and spark table, now I'm working on my PE table. All that I've read tells me that if my afr is low <12.7 that I need to subtract from my table and add if...
That did it!! I knew it had to be something simple! (it always is). Thank you for your help!!
Here is the screenshot
I don't understand, on my #4 user defined parameters Air Fuel Ratio, the function string is using 7101 PID. Where do you see that I'm using PID 2811? Am I missing something? Thanks for the help.
I have tried all I know a searched the forum over trying to get my AFR to log. Every time I connect I get a 'unsupported parameter'. I'm using my wideband through my A/C voltage to input the...
I got the problem 'unable to parse log' and tried the click and drag, but it will not let me drop it in the scanner. I also have some saved but when I do the file open from the scanner, I can't find...
Man do I feel stupid (more like humiliated). Now I know what happens when the coil pack on the right side is unplugged. The car run so good at idle, I didn't even realize it was not firing on the...
This is my next challenge. 2001 corvette z06, just installed long tube headers(coated) and high flow cats. I knew there may be issues w/ o2 sensors not working properly, so I wanted to check them...
Well, I read the sticky bout using outside power source, but I thought that it was referring to car charger adaptors for the laptop. I did not realize that it was for wall outlets too. I unplugged...
Laptop is a dell inspirion 1100 running xp. Is there any fix besides getting new laptop?
I can connect w/ scanner and read information and save logs, but when I go to editor and try to read the VCM I get the attached screen shot. I check pin 16 on obd port and get batt voltage. Why...
I just installed long tube headers and high flow cats and wanted to check the 02s and ensure they are working correctly. I know for the fronts, I'm looking for switching after heat up-what do I look...
Well I would have thought that with the power light on the mpvi interface coming on when I plug it up to the laptop that the usb cable was good-WRONG. Changed the usb cable and everything worked...
Is there a phone # that I can call?
No,but it dosen't appear to change any if I unplug or plug in the mpvi. Here is one w/ it plugged up.
Looked up the demos on taking sceen shot-it was blank, but see if this works-
check the attachment