Search:

Type: Posts; User: Jn2

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    13
    Views
    8,374

    Bump....do we have any updates to Windows for ARM...

    Bump....do we have any updates to Windows for ARM support? About to replace the old 2018 intel Mac with a M1 chip
  2. There literally a max delay learn value that...

    There literally a max delay learn value that answers this question. Max learn is 1 second stock, maximum capable if you raise it is 2 seconds
  3. Ditch the dual regs, run single reg with rails in...

    Ditch the dual regs, run single reg with rails in parallel and keep the DI pump fed off the OE 3/8" hose coming off the passenger side rail. Run your standard 55psi with boost/vacuum reference. Tune...
  4. Replies
    4
    Views
    1,754

    there is no difference in turning between a...

    there is no difference in turning between a normal 2018 mustang GT and one with the PP1, same shit other than gear ratios and other unrelated stuff to performance.
  5. Replies
    8
    Views
    2,975

    If you enabled the logic you need to repoll the...

    If you enabled the logic you need to repoll the PIDs for it to appear
  6. Replies
    28
    Views
    13,728

    can confirm this patch works, had a NA customer...

    can confirm this patch works, had a NA customer who always disabled the cams on high shifts bc of the old limiter, now he can shift at 8k w/o disabling VCT on the shifts
  7. Thread: E85 tune Stoich?

    by Jn2
    Replies
    3
    Views
    3,884

    Just leave it on 9.8,if you ever do get a e70...

    Just leave it on 9.8,if you ever do get a e70 fill STFT will just pull ~5%
  8. Replies
    30
    Views
    24,941

    Considering a write is required to changed the...

    Considering a write is required to changed the codes I do believe this is expected behavior. We have never been able to turn off codes w/o writing a new calibration in, which means licensing the...
  9. Replies
    6
    Views
    3,224

    there is a switch on Tricore's to manually set...

    there is a switch on Tricore's to manually set our idle, think it's called like idle override, you could enable to override and set it to something lower if you want.
  10. 15-17 use the gt350 motor with their 103mm TB,...

    15-17 use the gt350 motor with their 103mm TB, 18+ use a bullit motor with their 103mm TB
  11. Replies
    3
    Views
    1,313

    Stock gen 2 control pack file 92992

    Stock gen 2 control pack file


    92992
  12. Replies
    45
    Views
    19,337

    Where are you seeing the dwell test for the...

    Where are you seeing the dwell test for the coils? I just checked a auto and a manual copperhead and I don't see it anywhere, it's not under Engine>Spark or Engine Diagnostics>Misfire

    EDIT: Found...
  13. Thread: 1000cc injectors

    by Jn2
    Replies
    5
    Views
    3,331

    So you want to lie to your tuner about your...

    So you want to lie to your tuner about your injectors so they accept to tune the car?
  14. Replies
    45
    Views
    19,337

    updating now to see what's up

    updating now to see what's up
  15. Thread: IAT temp too high

    by Jn2
    Replies
    16
    Views
    6,256

    Copperhead prob doesn't have it if it's not...

    Copperhead prob doesn't have it if it's not there. Oh well, that would of been one work around, guess you should just do the plastic sensor instead.
  16. Thread: IAT temp too high

    by Jn2
    Replies
    16
    Views
    6,256

    Brass sensor is for 15+ cars only, 11-14's need...

    Brass sensor is for 15+ cars only, 11-14's need the plastic one(black with pink thread paste). If you wanna try and make it work then go grab a 15+ stock file and copy the IAT sensor data from it to...
  17. There are other limits in the trans section as...

    There are other limits in the trans section as well, you need to raise fuel cut limit, EOT, TOT, OSS, and other trans limit ones.
  18. Replies
    7
    Views
    4,041

    he's prob also hitting the EOT and TOT rev...

    he's prob also hitting the EOT and TOT rev limits...jsut applying the path doesn't let you rev higher, you still need to make sure everything else in the tune will allow it. All the patch does is...
  19. Thread: How to log MAF

    by Jn2
    Replies
    9
    Views
    2,601

    I only ever use BETA, I never bother using the...

    I only ever use BETA, I never bother using the other one
  20. Replies
    3
    Views
    1,275

    I usually always make composition 0

    I usually always make composition 0
  21. Replies
    2
    Views
    1,000

    post the datalog, one thing to keep in mind is...

    post the datalog, one thing to keep in mind is you wont hit max rpm in 7th bc it exceeds the factory speed limiter
  22. Thread: How to log MAF

    by Jn2
    Replies
    9
    Views
    2,601

    it doesn't happen with important channels, it's...

    it doesn't happen with important channels, it's usually some random obscure PID that causes it. Every important PID works
  23. Thread: How to log MAF

    by Jn2
    Replies
    9
    Views
    2,601

    this has been addressed already, you have a PID...

    this has been addressed already, you have a PID causing a conflict and this makes almost all other go gray.
  24. Replies
    15
    Views
    4,323

    There is no "part throttle" shift tables, there...

    There is no "part throttle" shift tables, there is only shift tables by mode(with most of those mods not being used on a mustang), those shift tables I modified are the shift tables that need to be...
  25. Replies
    7
    Views
    2,253

    I've ran .88 lama and 32* of timing, there is not...

    I've ran .88 lama and 32* of timing, there is not much power to be had going that lean though, ended up settling on .855 and 32* of timing.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4