Search:

Type: Posts; User: ahmedabri97

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Did you find out the issue? I am having same...

    Did you find out the issue?
    I am having same issue using same crank sensor adapter.
  2. Replies
    13
    Views
    7,957

    I am referring to the LT1/L86/L83. LT4 keep it...

    I am referring to the LT1/L86/L83.
    LT4 keep it stock data with stock camshaft and adjust it when you install a camshaft depending on the specs.
  3. Replies
    1
    Views
    1,271

    You need to adjust the virtual torque in the idle...

    You need to adjust the virtual torque in the idle rpm region.
    Ofcourse by lowering it.
  4. Replies
    42
    Views
    21,789

    You are welcome. Do you have good piston to...

    You are welcome.
    Do you have good piston to valve clearance with btr 227/242 cam in the 5.3?
  5. Replies
    4
    Views
    2,192

    Just put 1 in the adder in gears you want to...

    Just put 1 in the adder in gears you want to modify.
    Put the percentage you want to decrease in the adder modifier table and you are good to go.
  6. Replies
    38
    Views
    15,806

    No side effects.

    No side effects.
  7. There will be no difference.

    There will be no difference.
  8. Maybe the tuner is commanding excessive fuel...

    Maybe the tuner is commanding excessive fuel which causes the fuel pump to fall pressure or he messed with something.
    Another thing that can cause this issues is when the low side fuel pump fuel...
  9. Try copying the higher value of the 3 driver...

    Try copying the higher value of the 3 driver demand tables and pasting it on the rest which will make it snappier in all modes.
  10. What is the mods on the car? It may be you are...

    What is the mods on the car?
    It may be you are out fuel only.
  11. Replies
    38
    Views
    15,806

    Yes

    Yes
  12. Replies
    38
    Views
    15,806

    Yes you can add another 50% maximum, do not go...

    Yes you can add another 50% maximum, do not go too wild.
    The misfire counter will detect phantom misfire, therefore, you have to multiply the idle misfire tables by 1.5 to not encounter any misfire...
  13. Replies
    38
    Views
    15,806

    If you want it to chop more go to...

    If you want it to chop more go to engine>idle>rpm>adaptive>speed control>immediate table.
    multiply the values by 2 for columns -75 to 75 error and then make transition to the columns to the left and...
  14. Replies
    11
    Views
    8,611

    No need to gap the rings for that boost level...

    No need to gap the rings for that boost level (power level specifically).
    Most of us had good luck with stock gap in supercharger setups producing 650whp with a good camshaft kit.
  15. Replies
    11
    Views
    6,630

    Install the 12592525 red 3 bar map sensor. It...

    Install the 12592525 red 3 bar map sensor. It fits directly and the data:-
    linear= 312.5
    offset = - 11.25
  16. To retard timing on certain cylinders. Stock on...

    To retard timing on certain cylinders.
    Stock on some LT1 cars they come filled in certain cylinders at 5600 to 6400 RPM. I normally zero it out because when it retards timing it comes as knock...
  17. Replies
    11
    Views
    5,366

    2016 and upwards Sierra SLT all come with 8 speed...

    2016 and upwards Sierra SLT all come with 8 speed trans.
    I have a stock file for 5.3 w/ 8speed but I am away from the laptop, when I get time I will send it.
  18. Replies
    1
    Views
    2,132

    Bad pump unfortunately.

    Bad pump unfortunately.
  19. Replies
    2
    Views
    1,041

    If it is a bolts-on setup leave VVE stock it is...

    If it is a bolts-on setup leave VVE stock it is very accurate when stock.
    When you swap a camshaft tune VVE while putting VVT all zeros.

    For maf tuning VVT does not effect your tuning process...
  20. Replies
    29
    Views
    15,477

    Usually it does not effect factory cats but will...

    Usually it does not effect factory cats but will not sound that nice with cats.
    We do it all the time in the Middle East. 😂😂
    It seems to reduce spark plugs life by 25% maximum.
    No effect on the...
  21. Replies
    29
    Views
    15,477

    Email it to me I will do it for free....

    Email it to me I will do it for free.
    [email protected]
  22. Email support to add the channels in the next...

    Email support to add the channels in the next beta.
  23. Replies
    35
    Views
    13,716

    100% Required or car will not run.

    100% Required or car will not run.
  24. Replies
    8
    Views
    2,694

    If a zero degree cam phaser ( lockout) is...

    If a zero degree cam phaser ( lockout) is installed the actual intake cam angle will read zero at WOT.

    If you have freedom to play with vvt start with zeros in the table then try to retard 2...
  25. Replies
    8
    Views
    2,694

    Depends on the cam phaser limiter if it is a 0...

    Depends on the cam phaser limiter if it is a 0 degree lockout then playing with vvt will not help.
    Log actual intake cam angle.
Results 1 to 25 of 68
Page 1 of 3 1 2 3