Search:

Type: Posts; User: Emily89

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Drop a log here. Much more than simple torque...

    Drop a log here. Much more than simple torque request limit on this pcm
  2. Replies
    26
    Views
    4,148

    130165 this is what i notice. delivered torque...

    130165

    this is what i notice. delivered torque exceeds max torque allowed. driver demand over 100%. also notice traction control hits 100% during start. if confident peak torque table is high...
  3. Replies
    26
    Views
    4,148

    @chisleu you are exceeding max engine torque...

    @chisleu
    you are exceeding max engine torque and driver demand still. wastegate duty cycle looks under control now with that log
  4. Replies
    26
    Views
    4,148

    You are maxing driver demand and wastegate duty...

    You are maxing driver demand and wastegate duty cycle. They must be raised to achieve more.
  5. have u tried reducing lock speed below shift...

    have u tried reducing lock speed below shift speed?
  6. Replies
    19
    Views
    7,547

    most gracious thanks! If he reach out, I will...

    most gracious thanks! If he reach out, I will reach out tooo you also for second sets of eye
  7. Replies
    19
    Views
    7,547

    Why drag another name, when he self tunes? What...

    Why drag another name, when he self tunes? What is this? OP If you need help on tune LTG just dm I check when have time.
  8. Replies
    22
    Views
    8,085

    Yes, I have learn much since I post this so many...

    Yes, I have learn much since I post this so many years ago. I just have husband car on hub type dyno fo 2 days. I figure out cam timing easy this ways. Fuel was alreadys easyto manage. We do upgrade...
  9. Replies
    22
    Views
    8,085

    systems run blend mode way too redline from...

    systems run blend mode way too redline from stock. i think manufacturer has vve workink fine for cam angle. you can not even make edits to this angle on pcm if try and change angle of cam. its a...
  10. Is not intake problem. Need minor adjust only....

    Is not intake problem. Need minor adjust only. Nothing to cause this. I see fuel trim look fine. with 3% averags. Is a lot of slip rpm from switching gears. U need log WB EQ and DES MAP and any...
  11. Replies
    16
    Views
    6,296

    The E80 and E80A now both fully support flex fuel.

    The E80 and E80A now both fully support flex fuel.
  12. Replies
    15
    Views
    5,743

    ZZP has said recently that flex fuel is solved...

    ZZP has said recently that flex fuel is solved and working on new HPT beta.. But I also can not get it to read on 3 different cars :(
  13. Replies
    4
    Views
    6,756

    You have 0.000 set as your transmission gear...

    You have 0.000 set as your transmission gear ratio for 5 and 6 gear. Is that correct?
  14. Replies
    1
    Views
    1,212

    Hello, how did this work out for you? Did you...

    Hello, how did this work out for you? Did you need to adjust all of the spark tables to match?
  15. Hello again. I see you have made some improve!...

    Hello again. I see you have made some improve! Your actual torqu still seems to exceed you desire torque in some areas. This will close throttle on LTG. The fuel system is much limited also. You have...
  16. Hello. I have noticed in your file that...

    Hello.
    I have noticed in your file that all of the driver demand tables from 0-60 MPH are far too low in numbers. They are much less than even stock LTG numbers. Almost half. Perhaps this...
  17. Hello guys, are you use start of injection table...

    Hello guys, are you use start of injection table to increase injection time? You would raise these numbers?
  18. Replies
    15
    Views
    9,509

    When you calculate coefficients at 0 cam angle,...

    When you calculate coefficients at 0 cam angle, all cam angles also re caculate
  19. Can you also provides a log of this event?

    Can you also provides a log of this event?
  20. Thread: PE on or off??

    by Emily89
    Replies
    10
    Views
    3,487

    I too would like to be safe. Is using ltft + stft...

    I too would like to be safe. Is using ltft + stft vs maf a safe way to tune wot? I have set up a EQ error vs maf histogram. Would that be a better way in your opinion to tune WOT MAF? Also, thank you...
  21. Thread: PE on or off??

    by Emily89
    Replies
    10
    Views
    3,487

    Ok, thank you once again TCSS07. Just wanting to...

    Ok, thank you once again TCSS07. Just wanting to make certain Im not overlooking some things. Fuel trims are now very close after about 7 revisions +- 2% now for part throttle. I am happy with this....
  22. Thread: PE on or off??

    by Emily89
    Replies
    10
    Views
    3,487

    PE on or off??

    I am getting conflict of information on this issue. My 18 camaro turbo has factory wideband. I am tuning MAF part throttle too 4k, both high and low frequency, using histogram of ltft+stft math....
  23. Replies
    6
    Views
    3,898

    Driver demand needs more help sense you have...

    Driver demand needs more help sense you have raised turbo output. Should maybe do MAP C also
  24. Replies
    34
    Views
    20,884

    Most excellent mod! I too struggle to find decel...

    Most excellent mod! I too struggle to find decel spark table. If you could help point a direction, would be most grateful!!
  25. Replies
    79
    Views
    75,390

    YES! Thank you most kindly!!

    YES! Thank you most kindly!!
Results 1 to 25 of 45
Page 1 of 2 1 2