Search:

Type: Posts; User: TDCRacing

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    18
    Views
    19,081

    Thanks. This just helped me out

    Thanks. This just helped me out
  2. Replies
    55
    Views
    142,662

    TTT need hellp setting this up

    TTT need hellp setting this up
  3. Replies
    20
    Views
    12,923

    My ltft stopped showing up and instead showed 0...

    My ltft stopped showing up and instead showed 0 while attempting to do a maf tune. What am I doing wrong? I added the pid into the table. is there suppose to be a sensor uner the histogram?
  4. Replies
    1
    Views
    1,884

    Redownload the software and see if that helps....

    Redownload the software and see if that helps. First deleate the software from the control panel-add/remove programs.
  5. Replies
    20
    Views
    12,923

    When you say the primary section, You mean the...

    When you say the primary section, You mean the horizontal axis correct? I should not have any table listed under the vertical axis section due to the maf table not having a vertical section correct?
  6. Replies
    55
    Views
    142,662

    Bill or someone... Looking to maf tune a 2004...

    Bill or someone...

    Looking to maf tune a 2004 gto.

    Can someone explain to me why it would matter what year the ls1 is as to which config I should use? Looking for a maf tuning config and was...
  7. TTT

    TTT
  8. Ttt

    Ttt
  9. It looks like you may have something mixed up. In...

    It looks like you may have something mixed up. In the stock file I have posted in the first post while some numbers are zeroed out it looks like you have different information in the screenshot that...
  10. Mine is a M6 (Manual transmission) I do not...

    Mine is a M6 (Manual transmission) I do not belive these table are suppose to have anything listed. I have not changed anything at all. Someone correct me if im wrong.
  11. I verified and the tune that is listed on the...

    I verified and the tune that is listed on the first post is my factory tune.
  12. I'm confused, this should be the stock tune for...

    I'm confused, this should be the stock tune for my car that I saved before altering my current tune that I am working on now.

    What makes you think this is not mine. Ill check when I get back on...
  13. Regarding idle and the target idle speed table,...

    Regarding idle and the target idle speed table, Is this usually where to go and change values at if you want to obtain a lower or higher idle rpm?

    I know that is what I am trying to achive but...
  14. By the way I had two collapsed lifters. While...

    By the way I had two collapsed lifters. While some valvetrain noise on startup is normal it suprises me that I did not hear anything more. Will hopefully have everything back together in the morning....
  15. Before posting this I read about increasing idle...

    Before posting this I read about increasing idle to 950. I will do that. Add 5g/sec across the whole idle airflow vs. coolant temp vs gear table. Done.

    Is the idle airflow mainly have control...
  16. Cam specs: .644 .598 111 LSA Duration...

    Cam specs:

    .644 .598

    111 LSA

    Duration 231 234

    Mods in SIG
  17. Lol I ment to say I pulled the plug wires. Not...

    Lol I ment to say I pulled the plug wires. Not the plugs them selves. I can only imagine how that would feel.

    I have known working parts from othe lsx engines. Looks like tomorrow I will be...
  18. Replies
    8
    Views
    4,545

    Ttt

    Ttt
  19. Also could this issue have caused my increased...

    Also could this issue have caused my increased map kpa's at idle?
  20. pulling both plugs on cylinders that are...

    pulling both plugs on cylinders that are suspected dead resulted in no engine running change. There dead for sure. Now I wonder why.....

    what should i be looking for on the missfire section? never...
  21. I have been looking over the car for mechinical...

    I have been looking over the car for mechinical issues and I think I have found the issue. Two dead cylinders on the same bank. Cylinders 6 and 8. The tubes on the new stainless steel headers I just...
  22. I noticed the timing at idle as well ( or from...

    I noticed the timing at idle as well ( or from 0-1700 rpm's). At times I was running negative timing. At first the car idled fine. IT was running open headers. The car would actually idle around 850...
  23. Ttt

    Ttt
  24. Help needed on initial startup for H/C/I install. Car will barely run.

    Where should I go first in attempting to get this thing to idle? Car will not run enless I give it 20% throttle. Stalls if I give it less than 10% throttle.


    Decent size cam .602/.648 112 with...
  25. Replies
    11
    Views
    11,200

    I was assuming I had I set up a pid for the afx...

    I was assuming I had I set up a pid for the afx wideband to read correctly?
Results 1 to 25 of 249
Page 1 of 10 1 2 3 4