Search:

Thanks for your help

I will adjust the PE mode, I have not seen it.

BTR LS3 STAGE 2 V2 CAMSHAFT
221/24X, .619/.617, 113 LSA

Intake tube is K&N LS3 ( Camaro 2012)

I just did a quick scan...

Thanks for the help

I will try that

Thank you for your help

When I calibrated the VE and drive without MAF in open loop it was gone completely.

There is a K&N Intake installed (2012 Camaro )

If I just turn off the closed loop...

Hello

I have a surge while cruising.

Vehicle is a 1971 Chevelle Ls3 4l80e BTR Stage 2 V2 Cam.

I calibrated the MAF and VE LTFT below 5% and smoothed the ignition table.

But I still have a...

I have tried another original MAF without change.

The problem is also only in first gear.

On the dyno it does not do it at all.

I still have to check the wiring harness

Thanks

Engine Trailblazer SS LS2 4l70e Corvette Intake Manifold, Cold Air Intake.

I have the problem that he is in first gear at Full throttle from 5500 is too lean.

The Injectoin time goes down and...

Thanks for your Help

I have not senn That is make on the downshift.

Okay I thought that he only reduces the shift torque


@ 10,22 in the scan the Timing goes down to 4 degrees.

and @ 11.16.


thanks

1971 Chevelle Stock Ls3 4l80e

The car runs grat but sometimes pull Timing at Wot.

In the Scan I see that the Torque MGT is active.

I have taken out all known torque limits.

You can see...

1971 Chevelle with Ls3/4l80E PSI Harnes and Ecm


Does anyone have an idea why it takes so much Timing back.

Can make something other than the knock sensors Knock retard ??


Thanks for...

When I buy an ecm and have it programmed

Does that work without reprogramming the Tcm?

I have tried that once has changed nothing.

I guessed the ecm has a defect when it gets really warm in the engine compartment it sometimes goes with the gearbox
then fits outputshaft speed ttc...

Thanks for your Help

I can SPS programming gm to 2005 with the Tech 2.

I also have an orginal MdI.

Would be interesting for us because we also many 6l80e Trans builds and can then also...

okay I will test it tomorrow with the ground first.

thanks for your Help

Hello

You need to make a scan file with the vcm
scanner.
And let it run for a few minutes at idle.

No one will be able to help you here without information.

Hello

I have a problem.

The Ecm detects 4wd low active. The Syclone does not have a 4wd low tranvercase.

(Problem no TCC function early Shifts)

And I didn't connect a cable to the pin.

When I drive and he runs longer at idel and I continue to drive he switches as programmed.

I had that 3 times now

Has anyone an idea

Hello

I tune a Syclone with LS3 with 4l65e.

But the part trottle schifts do not fit with the table.

He schift much too early

thanks for Help 114999115000

Hello
the Variations learn does not work.

Tried with Snap on and Tech,Vcm

Tech2 writes Diag.faults currently active

But there are no error codes in memory

Can someone help me

yes so I will do it

thanks

Hello I was hoping to do a segment swap on Ls3. But i did not find anything with the OS.

How can I do it ???

thanks for help

okay thanks for help comandet Afr is now on 12.5
the current afr is still at 14.5 will now tune the MAF

thanks

okay that try thanks
is enable torq the same as engine load in vcm scanner ????

Hello I have here a Factory five with 2002 corvette ls1.

does no power enrichment.
I can not find the problem .I hope someone can help me!!!!!!

Thanks