Search:

Type: Posts; User: yonson

Page 1 of 10 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    756

    2006 Silverado SS stock read needed

    Does anyone have a known stock read for a 2006 Silverado SS? I checked the repository but the only SS file in there is not stock.
  2. Ok, you are good then. As long as you don't...

    Ok, you are good then. As long as you don't stray too far away from the Roush cal when it comes to emissions side you should be able to get the monitors to run and set, although the LT's will cause...
  3. Did you start from the Roush cal or something...

    Did you start from the Roush cal or something else?

    The mode 6 data is basically the results from the PCM after checking for monitors and faults. It's just a small piece of the puzzle that is...
  4. Post your stock file...

    Post your stock file...
  5. Replies
    16
    Views
    5,812

    Is your bypass hooked up to the boosted side or...

    Is your bypass hooked up to the boosted side or the vacuum side?
  6. Replies
    0
    Views
    859

    Opening .csv file with VCM scanner

    This use to work quite easily, however now when I try to open a .csv file I'm getting an Open File error that states "Unable to open file. Incorrect file header."

    What header is it looking for? ...
  7. Replies
    25
    Views
    7,586

    Most likely heat soak. Take a look at your IAT...

    Most likely heat soak. Take a look at your IAT spark retard.
  8. Nice! However, shouldn't this be in the...

    Nice!

    However, shouldn't this be in the Ecoboost section ;)
  9. Is there a stock file available?

    Is there a stock file available?
  10. Replies
    7
    Views
    9,955

    Thanks again, I was just concerned when the file...

    Thanks again, I was just concerned when the file was only 139kb, but everything seems to have worked fine.
  11. Replies
    7
    Views
    9,955

    Interesting, so the TCM can't be calibrated on...

    Interesting, so the TCM can't be calibrated on those? The ECM reads fine, however the file is quite small (less than 200kb).
  12. Replies
    7
    Views
    9,955

    2004 LB7 Auto TCM read failure

    I tried reading out a friends 2004 LB7 and using both 3.6 and 3.7 Beta I get a read or timeout error when trying to read the TCM this happens when trying to do a read entire on the ECM/TCM together...
  13. Did you try raising the neutral rev limiter?

    Did you try raising the neutral rev limiter?
  14. Replies
    4
    Views
    1,462

    Congrats! Although, I'd do an OPG and CG and...

    Congrats!

    Although, I'd do an OPG and CG and run it to 7500 like it sits, no pulley needed :)
  15. Replies
    42
    Views
    15,666

    You've got some issues that should be addressed...

    You've got some issues that should be addressed before you take it WOT anymore, .95 lambda on .8 commanded at WOT isn't good...

    Can you post your stock file too.
  16. Replies
    6
    Views
    2,022

    You need to log the Mapped Point Weight for each...

    You need to log the Mapped Point Weight for each one that is being used (Mapped Points Configuration table) and it will give you a percentage of which point is being used. The mapped points are...
  17. It uses the Tq. Reduction Upshift/Downshift...

    It uses the Tq. Reduction Upshift/Downshift tables, if you want to reduce the amount of spark being pulled on the gear change raise those tables, although that will in effect slow down your shift...
  18. Replies
    1
    Views
    1,143

    Ford Standalone logging

    Is this ever going to be implemented? Logging at the dragstrip with a laptop in the vehicle is a PITA...
  19. Replies
    18
    Views
    8,988

    Nice!

    Nice!
  20. That's only on the supercharged vehicles...

    That's only on the supercharged vehicles...
  21. Interesting, that's pretty much identical to the...

    Interesting, that's pretty much identical to the Roush PP cal...
  22. It's not just the VIN that is used for licensing....

    It's not just the VIN that is used for licensing. On my 2016 F-150 I had licensed the factory cal, later on I had the N/A Roush calibration flashed in with their software, when I read that out with...
  23. Replies
    107
    Views
    237,694

    SO FRUSTRATING that they won't add this back in...

    SO FRUSTRATING that they won't add this back in...
  24. Replies
    1
    Views
    1,473

    https://www.hptuners.com/forum/showthread.php?6458...

    https://www.hptuners.com/forum/showthread.php?64589-2015-vortech-tune&p=483297&viewfull=1#post483297
  25. Replies
    9
    Views
    5,585

    Install the plate and tune for peak torque...

    Install the plate and tune for peak torque...
Results 1 to 25 of 234
Page 1 of 10 1 2 3 4