Search:

Type: Posts; User: ZincGT

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Neutral Down Skip - disable to eliminate torque...

    Neutral Down Skip
    - disable to eliminate torque management on downshift skip shifts via neutral

    Sync Down Skip
    - disable to eliminate torque management on downshift skip shifts at sync (not sure...
  2. please log with these channels 127778

    please log with these channels 127778
  3. Replies
    10
    Views
    1,925

    adjust your maf curve and VVE, keep PE the same....

    adjust your maf curve and VVE, keep PE the same. Need to keep the injectors around 5.5ms and the tq reading will be decent. You can add tq to the tq model if need, don't go crazy though.
  4. Replies
    6
    Views
    945

    you need to log more info 127304

    you need to log more info 127304
  5. Thread: Cam Adjusting

    by ZincGT
    Replies
    2
    Views
    830

    The higher the number the more retarded

    The higher the number the more retarded
  6. Replies
    8
    Views
    1,715

    This worked thank you. I had to find a stock file...

    This worked thank you. I had to find a stock file but it carries commanded eq all the way through now.
  7. Replies
    8
    Views
    1,715

    Its a closed loop system, I can add as much as I...

    Its a closed loop system, I can add as much as I want but its commanding a higher a/f so the actual a/f will follow it and pull the fuel back out.
  8. Replies
    8
    Views
    1,715

    Hellcat Commanded EQ Ratio goes lean at WOT

    Trying to clean up a tune for a friend on his trackhawk, the vehicle has a cam and is stock otherwise. Doing a 5th gear pull on the dyno around 5200 rpm the commanded eq ratio starts going lean, I...
  9. Replies
    26
    Views
    7,402

    driver demand

    driver demand
  10. Replies
    1
    Views
    734

    2020 ZL1 limited pids in scanner

    Just curious if I am missing something on this. I've downloaded the new beta software, updated the firmware on my MPVI2 but on this 2020 ZL1 I cant log near enough pids i need to be useful. No issues...
  11. Replies
    6
    Views
    1,799

    Your car is asking for 50% more fuel in some...

    Your car is asking for 50% more fuel in some areas. leave the spark alone and work on dialing in your maf curve and ve tables.
  12. If I was tuning this car, based off the data that...

    If I was tuning this car, based off the data that you logged I would add at least 5% to the MAF curve at WOT (you need to log maf hz to figure out where to add the fuel) and disable burst knock then...
  13. 2017 a10 zl1

    2017 a10 zl1
  14. 106942 This from my personal car

    106942

    This from my personal car
  15. Do you still need this?

    Do you still need this?
  16. Replies
    12
    Views
    2,694

    Just wanted to update this, cats failed and...

    Just wanted to update this, cats failed and plugged the exhaust and mufflers.
  17. Replies
    9
    Views
    3,054

    Your MAF Hz reads abnormally low when you are...

    Your MAF Hz reads abnormally low when you are going WOT... the values are higher at idle then WOT.
  18. Replies
    3
    Views
    1,676

    need more then just the tune, whats the setup?...

    need more then just the tune, whats the setup? fuel? post a previous WOT log
  19. Replies
    0
    Views
    1,200

    2.3 Ranger next step

    103947
    103948

    Got bored and decided to make an attempt at tuning my daily, I followed the SHO tuning guide and made some adjustments slowly been adjusting things. Just curious on how I should...
  20. Replies
    2
    Views
    1,525

    Your injector flow data is not setup correctly,...

    Your injector flow data is not setup correctly, assuming your injectors are 1000cc (95.2 lb/hr)at 43.5psi that puts them at 110 at 58psi. I would scale everything by 1/2.
  21. Your log does not indicate that you have a break...

    Your log does not indicate that you have a break out harness.
  22. You need to get a break out harness for your baro...

    You need to get a break out harness for your baro sensor in your maf. Look at your log, its updating the baro while in boost which is not accurate. These cars function on P Ratio and having...
  23. Replies
    12
    Views
    4,207

    0 out prediction coefficients

    0 out prediction coefficients
  24. Replies
    12
    Views
    2,694

    Thank you. I think the next step is to pull the...

    Thank you. I think the next step is to pull the blower off and see if it has wear on the rotors. Could this be a throttle body issue?
  25. Replies
    12
    Views
    2,694

    I wasn't sure if it was correct or not. The...

    I wasn't sure if it was correct or not. The period reads correctly and airflow estimates seem correct....
Results 1 to 25 of 211
Page 1 of 9 1 2 3 4