Search:

Type: Posts; User: rpmextreme

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Did you ever figure out the P2805 issue? I think...

    Did you ever figure out the P2805 issue? I think it has something to do with the fact that the early 10L80 used a different internal range switch compared to the later ones. Im not sure if you can...
  2. Replies
    9
    Views
    1,843

    These will work as well. We had these out long...

    These will work as well. We had these out long before Speartech copied them. http://www.rpmextreme.com/Category/70/Jeep-JK-LS-Swaps.aspx
  3. I can "read" the E92 and T93. Well HPT supplied a...

    I can "read" the E92 and T93. Well HPT supplied a "stock read file" then I can make changes to the TCM file and license it..... but it fails to write the unlocked T93 no matter what I try. It does...
  4. Still no luck on writing a tune to a T93 TCM from...

    Still no luck on writing a tune to a T93 TCM from my bench harness.
  5. Replies
    2
    Views
    1,553

    you need to turn Baro Leanring off.

    you need to turn Baro Leanring off.
  6. Replies
    6
    Views
    1,387

    I think out may be a HP tuners scanner issue...

    I think out may be a HP tuners scanner issue showing Unknown 82 while in drive and manual mode. I have seen this on several working, driving 8L90s wi no issues. I think maybe they don't have their...
  7. Replies
    2
    Views
    2,909

    I second this.

    I second this.
  8. So I tried again with a different T93. Bought a...

    So I tried again with a different T93. Bought a used T93 for a 10 speed. sent it to HPT to be unlocked.
    Got it back and plugged it into the bench harness and "read" the TCM, took the HPT supplied...
  9. Can you read and write to an unlocked T93 without the ECU being used?

    We have a L86 6.2 10L90 installed in an older vehicle. We are running a 2017 E92 ECU and a T93 (unlocked) for the 10L90.
    We have ran others with a 2017 ECU and T87a 10 speed but for some reason...
  10. Replies
    6
    Views
    2,585

    Ever find a way to upload those files?

    Ever find a way to upload those files?
  11. Replies
    41
    Views
    10,499

    I just plugged in a MPVI3 and it came right up...

    I just plugged in a MPVI3 and it came right up and asked to connect to MAC or Windows. Chose windows and now the software will sync. MAC M1 Windows 11 running in Parallels.

    FYI still can't get...
  12. The new Version 5 will open on a MAC running...

    The new Version 5 will open on a MAC running windows 11 via Parallels software. But I still can't get the MPVI2 to recognize. The drivers look to be installed but when I go to resync, it does...
  13. Replies
    41
    Views
    10,499

    The new Version 5 will open on a MAC running...

    The new Version 5 will open on a MAC running windows 11 via Parallels software. But I still can't get the MPVI2 to recognize. The drivers look to be installed but when I go to resync, it does...
  14. Windows 11 HPT Editor and Scanner won't open but BETA versions will

    I have been running an older MAC pro with windows 10 running Virtual using parallels desktop. It has always worked great. I upgraded to a new MAC mini studio with the new Apple M1 processor. With...
  15. Replies
    2
    Views
    962

    what calibration do you have in the TCM...

    what calibration do you have in the TCM currently? corvette or truck?


    If you switch the OS then you will have to send the TUTD signal via the canbus with either a BCM or a module. the corvette...
  16. Replies
    6
    Views
    2,585

    I don't think it will let you do the TCM...

    I don't think it will let you do the TCM replacement with a T87. that option will only show up if you have a T87A plugged in. You may be able to plug in a T87a and when it asked you to read the...
  17. Replies
    6
    Views
    2,585

    TUN Module files for T87 T87A

    So I was thinking of a way to make programing in the TUN (solenoid data) on the T87-T87A style TCMs a little easier.

    Right now you can use the HP Scanner (beta) to "replace" a T87A. You take your...
  18. Yes we took a T87 and had it programed with the...

    Yes we took a T87 and had it programed with the correct TUN data and it works fine. What I am seeing is even though you buy a "pullout" and they say that the ECU and TCM were from the same vehicle,...
  19. This should work for the E92 as well. EZCANBUS...

    This should work for the E92 as well. EZCANBUS Alternator Control module
  20. Replies
    2
    Views
    2,385

    This is a good one PCAN-USB...

    This is a good one PCAN-USB. it comes with the basic Pcan View software.

    PCAN-Explorer is their higher end software and can do a lot more than the base PCAN-VIEW. I use PCAN-VIEW for 90% of the...
  21. Replies
    6
    Views
    1,789

    If you want the GM ECU to control the compressor,...

    If you want the GM ECU to control the compressor, Idle and fans you will need the GM high side pressure sensor hooked up and working.
    You will also need one of these AC REQUEST MODULES to send the...
  22. Replies
    6
    Views
    4,321

    I just did one. You have to have the trans up to...

    I just did one. You have to have the trans up to at least 160 degrees, your foot on the brake and the parking brake applied. then when you click on the learn button you will then put it in drive,...
  23. We have this Jeep at Rpmextreme. Our conversion...

    We have this Jeep at Rpmextreme. Our conversion harness does have the inputs for the parking brake switch and all the different brake switch inputs so a relearn will run and complete. Opening the...
  24. Replies
    3
    Views
    1,273

    http://www.rpmextreme.com/Product/289/GM-E38-PWM-F...

    http://www.rpmextreme.com/Product/289/GM-E38-PWM-FAN-CONTROLLER.aspx

    We can program this module to control a Spal fan from a E92 ECU.
  25. Replies
    11
    Views
    4,801

    You may need to stop recording then try the trans...

    You may need to stop recording then try the trans reset parameters.
Results 1 to 25 of 157
Page 1 of 7 1 2 3 4