Search:

Type: Posts; User: Boody78

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    877

    It's labeled throttle inlet characteristics....

    It's labeled throttle inlet characteristics. Enter the slope and offset for your new sensor.
  2. Replies
    4
    Views
    1,605

    I had the same issue with my 2017 twin turbo V6....

    I had the same issue with my 2017 twin turbo V6. Try this... Under Airflow>Electronic Throttle>ETC PR Filtering, set it to 0.4 for the entire range.
  3. Replies
    1
    Views
    743

    No, if you are using a stock pump then these ARE...

    No, if you are using a stock pump then these ARE the values for that pump. You are correct that adjusting them would trick the ecu into holding the injectors open longer, but If the pump is maxing...
  4. Replies
    31
    Views
    18,603

    In the scanner I have available "Indicated Torque...

    In the scanner I have available "Indicated Torque Reference". Does this represent the "Indicated Torque" or the "Indicated Estimated Torque"?
  5. Twin Turbo 3.7L V6 part throttle stumble under boost SOLVED!

    Finally after 2 years of trying every method I could find on this forum and the cookbook I have found a solution to my issue.

    What I have deduced by reading lots of posts is that the way the...
  6. +1 for V6 support if possible please.

    +1 for V6 support if possible please.
  7. Replies
    115
    Views
    65,523

    I agree completely that it makes no sense which...

    I agree completely that it makes no sense which is why it's so frustrating. It's just the only thing I've tried that actually improved the IPC error. I've tried about a half a million other things...
  8. Replies
    115
    Views
    65,523

    So I've been working on eliminating ipc error for...

    So I've been working on eliminating ipc error for a couple months. The only thing that seems to work is actually lowering the values on the torque tables and calculating the inverse. I can not...
  9. Replies
    115
    Views
    65,523

    It seems to me like something I'm doing in the SD...

    It seems to me like something I'm doing in the SD table using this method is causing the throttle to not close under low load.
  10. Replies
    115
    Views
    65,523

    Thanks for the help guys, The system uses...

    Thanks for the help guys,

    The system uses vacuum operated re-circulation valves. They are connected directly to the turbo housings, I installed a couple nipples into a TB Spacer I already had for...
  11. Replies
    115
    Views
    65,523

    I'm tuning the SD tables by locking in each...

    I'm tuning the SD tables by locking in each specific map point and applying the method outline here https://forum.hptuners.com/showthread.php?68007-Ford-Speed-Density-Calculator

    The only changes I...
  12. Replies
    115
    Views
    65,523

    Thanks for rsponding. My car is a 2017 3.7L, It's...

    Thanks for rsponding. My car is a 2017 3.7L, It's 100% Speed density no MAF at all. I've installed twin f150 ecoboost turbos. I'm trying to start out conservative. I'm maxing out around 7psi of boost...
  13. Replies
    115
    Views
    65,523

    I'm a noob. I was getting quite a bit of IPC...

    I'm a noob. I was getting quite a bit of IPC error. I've managed to cut it down considerably, but it's still causing trouble. I've scaled the Load axis on the torque tables up to 1.4 because I've...
  14. Replies
    115
    Views
    65,523

    I'm a little lost, but I think you are saying...

    I'm a little lost, but I think you are saying there is a direct relationship between the axis values of each table so if one is changed the other needs to also. If I'm understanding this correctly,...
  15. Replies
    115
    Views
    65,523

    Could you explain this a little more? Using your...

    Could you explain this a little more? Using your method I've managed to get my throttle to stay open under load, but now i'm getting rev hangs when I back off the pedal.
  16. Thread: New Guy

    by Boody78
    Replies
    11
    Views
    3,137

    Yea I saw that. It's how I realized that the...

    Yea I saw that. It's how I realized that the "pre-release" data they did send me was wrong. The things that should carry over were completely different. I can't find any way to convert GM data to...
  17. Thread: New Guy

    by Boody78
    Replies
    11
    Views
    3,137

    You seem to be missing what I'm saying. They do...

    You seem to be missing what I'm saying. They do not have data for these injectors. Please take a look at their site and let me know if you find it.
  18. Thread: New Guy

    by Boody78
    Replies
    11
    Views
    3,137

    They do not have data for the injectors I...

    They do not have data for the injectors I purchased. They emailed me "pre-release data" after I complained, and asked me for my feedback. The data that they provided was calibrated at 3bar, and even...
  19. Thread: New Guy

    by Boody78
    Replies
    11
    Views
    3,137

    That's a nice setup! I purchased injectors that...

    That's a nice setup! I purchased injectors that were advertised for the 3.7 from DW. Even though their website stresses that they are all about data imageine my surprise that when my $400 injectors...
  20. Thread: New Guy

    by Boody78
    Replies
    11
    Views
    3,137

    I'm also tuning my 3.7. Did a ecoboost twin turbo...

    I'm also tuning my 3.7. Did a ecoboost twin turbo kit. I'm also learning as I go. Working on my injectors right now. Turns out our cars fuel system is more like the Australian cars. Any injector data...
  21. So trying to answer my own question: The fuel...

    So trying to answer my own question:

    The fuel rail pressure is a constant 4bar, this never changes. So the differential across the injector would be 4bar which is 58.02psi - gauge pressure in the...
  22. Sorry to revive an old thread. Am I understanding...

    Sorry to revive an old thread. Am I understanding correctly? This would be 4bar above gauge pressure in the manifold correct? That would be the pressure differential across the injector? This is what...
  23. Parameter has been added in the latest beta!...

    Parameter has been added in the latest beta! Thanks Eric!
  24. I have a manual.

    I have a manual.
  25. Thanks for the response. Unfortunately the...

    Thanks for the response. Unfortunately the parameter is not included in the latest BETA either. I guess I'll put in a request. I've read through several threads and I can't find any so far that...
Results 1 to 25 of 27
Page 1 of 2 1 2