Search:

Type: Posts; User: bstroked

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. So even if you turn off the adaptives they still...

    So even if you turn off the adaptives they still need to be cleared? And when you guys talk about sending a request to support to add something, do you just ask for a certain thing to be added or do...
  2. Thanks. I'll see what i can figure out with the...

    Thanks. I'll see what i can figure out with the anticipated and torque based stuff... I've disabled the torque reduction and some of that stuff but haven't done anything with anticipated. I've...
  3. How do I shorten the offgoing clutch? I've read...

    How do I shorten the offgoing clutch? I've read and read and tried many different things and combinations, adaptive on and off, and can't seem to get very noticeable results. I'm pretty sure my...
  4. Replies
    6
    Views
    3,180

    That's an explanation that finally makes sense to...

    That's an explanation that finally makes sense to me. I tried the tune and hit 1022 ft tq! Thanks a lot! Those lambda settings must mess with the torque readings and not just cut the top end out. My...
  5. Replies
    6
    Views
    3,180

    Thanks, I'll give it a try tomorrow... I've never...

    Thanks, I'll give it a try tomorrow... I've never had the lambda explained to me in a way that sinks into my hard head... I've messed with it before by lowering the whole table down to .500. The...
  6. Replies
    6
    Views
    3,180

    Here's my tune. 103629 I've changed all the...

    Here's my tune. 103629 I've changed all the torque limiters I've been able to find.
  7. Replies
    6
    Views
    3,180

    Adjusting Indicated Torque?

    Does anyone have any pointers on how I can get my 2015 6.7L torque above 815 ft lbs at WOT? I've found a few things on here of stuff to change and tried them but nothing seems to make any difference....
  8. Replies
    7
    Views
    3,886

    If that's the case, will the psi be reflected in...

    If that's the case, will the psi be reflected in the line psi PID in the scanner? I had my oncoming psi raised quite a bit and it didn't seem to effect the reading. 🤷
  9. Replies
    7
    Views
    3,886

    I had to get back to work, so quit fooling with...

    I had to get back to work, so quit fooling with mine, again...I was having trouble with 4-5 shifting right at half throttle.. Sometimes it would slip all the way to 6th , and sometimes it would make...
  10. Replies
    7
    Views
    3,886

    6r140 PSI question's

    I've been trying to tune for more power (without much luck so far). On my 15 I've only found a " desired line psi" parameter on the scanner. When I read about guys who are up at 300psi, is that line...
  11. Thanks. I think that helps. I'll keep working on...

    Thanks. I think that helps. I'll keep working on it. I think might finally be wrapping my mind around this thing. I haven't found E clutch psi or gear ratio for my 15 yet... I have it doing not to...
  12. Are these the right PIDs to monitor? And what is...

    Are these the right PIDs to monitor? And what is it doing when one is coming on while the other is still going off? If you can look at my log file, does it look normal?
    99089
  13. Replies
    3
    Views
    1,509

    BD pressure enhancer opinions?

    Just wondering what everyone thinks about these https://us.bddiesel.com/products/6r140-pressure-enhancer?variant=30073626820672 ? Is it not possible to raise the line pressure with tuning? Or is...
  14. Replies
    16
    Views
    6,004

    When you say "bumped up pilot timing", how much...

    When you say "bumped up pilot timing", how much are you going? 2 deg or 5deg? I bumped mine about 2 deg in "map 1 config 2 mode 0" but there is really d any noticable difference. Also I've been...
  15. So if CLADP is disabled, is the adaptive tab...

    So if CLADP is disabled, is the adaptive tab totally obsolete? And how much line psi during shift are you all adding? 10,20,50 psi?
  16. Replies
    2
    Views
    1,358

    I thought so. I haven't actually personally read...

    I thought so. I haven't actually personally read one. It was just one I found on here that was posted fairly recently, but it still might not have been read, I guess...
  17. Replies
    28
    Views
    11,886

    Yep, your right!!! I installed the latest update...

    Yep, your right!!! I installed the latest update (I guess) and now it seems to work!!! Thanks
  18. Replies
    28
    Views
    11,886

    Figured it out!!! It doesn't work to base offset...

    Figured it out!!! It doesn't work to base offset 0x80000000 or above in TunerPro V5. It has to be done in text editor.
  19. Replies
    2
    Views
    1,358

    Can't Find FICM Tab!!!

    I don't have a 6.0, but like getting ideas from the different engines. About a year ago I looked at a tune and it had the FICM tab, now when I look there's only Pilot Injection Tab in that spot. I...
  20. Replies
    1
    Views
    2,320

    I can't seem to find the right map in HPTuner's....

    I can't seem to find the right map in HPTuner's. The only one I find is "EBP desired setpoint". I've used the Minotaur Software to tune mine for a long time now. I believe the maps in it are the...
  21. Replies
    28
    Views
    11,886

    I think that might be the problem too, but I have...

    I think that might be the problem too, but I have yet to figure out how to offset the whole bin file. In TunerPro it seems like that base offset under xdf header only offsets where the definition...
  22. Replies
    3
    Views
    1,658

    I haven't looked at the tune yet, and don't know...

    I haven't looked at the tune yet, and don't know much about the 6.0L. I've been tuning my 7.3L for quite a while already with a different software and I think they're a lot the same. Did you make...
  23. Replies
    28
    Views
    11,886

    So it's normal not to be able to add basic...

    So it's normal not to be able to add basic parameters? I was trying to figure out if I was out in left field with what I found. I was starting to wonder if there's a bin offset I need to do to the...
  24. Replies
    28
    Views
    11,886

    So what do you do if the tables you want to add...

    So what do you do if the tables you want to add are not in the allowed addresses? I think I found one of the Engine Brake tables for the 2015, but the address is nowhere near the allowed ones. I'm...
  25. Replies
    17
    Views
    9,173

    This is what I've been looking for all day!!!! PM...

    This is what I've been looking for all day!!!! PM Sent!
Results 1 to 25 of 37
Page 1 of 2 1 2