Search:

Type: Posts; User: ericwilloughby

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Thanks. I do use the OEM idle base spark. 13...

    Thanks. I do use the OEM idle base spark. 13 degrees. That 2nd tune above is the actual daily driving tune, except for 24 degree minimum final spark. the 24 degree everywhere tune was just a...
  2. Please correct me if I'm wrong here but this is a...

    Please correct me if I'm wrong here but this is a manual transmission and commanded throttle is only 11-13% when this oscillation takes place. Does torque management do anything on these low throttle...
  3. We have a winner

    Disabling spark smoothing dramatically reduced the rather violent jerking I've been enduring for years. It's still there but only a fifth of what it used to be which makes it unnoticeable most of the...
  4. EVERYTHING, I think, is set to 24 degrees. I...

    EVERYTHING, I think, is set to 24 degrees. I will disable spark smoothing but 24 smoothed to 24 shouldnt be a problem, hahaha

    101767
  5. You mean like this.? overspeed is zero and idle...

    You mean like this.? overspeed is zero and idle costdown is 24. EVERYTHING is set to 24. and its going down to 5 somehow.101764
  6. Rapid timing oscillation, will pay for a solution

    2008 LS3 Corvette M6, BTR 225/238 cam 50k miles E50

    Fuel trims have been tuned in VVE and combination VVE MAF.


    I have a rapid timing oscillation under light load, level surface driving, in...
  7. 12's and this is handy 100794

    12's and this is handy

    100794
  8. Replies
    109
    Views
    152,203

    Thanks for the reply. I never figured out a way...

    Thanks for the reply. I never figured out a way to compare. Took a while to learn to tune vve. I found it much easier once I learned to use the correct manifold switch option and zeroed out the other...
  9. Replies
    109
    Views
    152,203

    Is there a way to use the compare function to...

    Is there a way to use the compare function to compare old and new VVE portions of the tune? At this time when I'm looking at a VVE table I can't look at anything else until I close that window.
  10. Replies
    109
    Views
    152,203

    I have no idea how to use the vve editor. is...

    I have no idea how to use the vve editor. is there a guide?
    This is really beginning to piss me off. I miss the old "411"ecm.
  11. Replies
    3
    Views
    2,551

    I'm not positive but I didn't think 2nd was a...

    I'm not positive but I didn't think 2nd was a option with the trans break.
  12. Replies
    14
    Views
    6,065

    Maybe I'm retarded but all I see are serial and...

    Maybe I'm retarded but all I see are serial and they don't work 79963
  13. Replies
    14
    Views
    6,065

    Yeah. I gotta say I'm not happy with the new...

    Yeah. I gotta say I'm not happy with the new site. It's "pretty" and showcases there new products but it sucks for support.
  14. Replies
    14
    Views
    6,065

    Ah, I'm here because I can't find my application...

    Ah, I'm here because I can't find my application key in the new website. Any suggestions.
  15. Replies
    14
    Views
    6,065

    looks like the new website is here. 12 years...

    looks like the new website is here. 12 years later, haha
  16. Replies
    10
    Views
    6,667

    Also.. Does klf apply to the entire table or is...

    Also.. Does klf apply to the entire table or is the table divided into cells and a different KLF for each area?
  17. Replies
    10
    Views
    6,667

    K.. Thanks.. 95% of the time I buy E85 but I...

    K.. Thanks.. 95% of the time I buy E85 but I found 87 octane for $2.20 since I'm not FI I went for it. Didn't know it had pulled timing from 26 degrees down to 16 until I happened to log. I'd never...
  18. Replies
    10
    Views
    6,667

    Looks like flashing the modified low octane table...

    Looks like flashing the modified low octane table reset the klf. Thanks anyway. 1st I've heard of klf. Was it also on the Gen 3 ecm? I thought timing just switched between the 2 tables not a mixture
  19. Replies
    13
    Views
    6,944

    Looks like flashing the modified low octane table...

    Looks like flashing the modified low octane table reset the klf. Thanks anyway. 1st I've heard of klf. Was it also on the Gen 3 ecm? I thought timing just switched between the 2 tables not a mixture
  20. Replies
    13
    Views
    6,944

    I don't have E85 tables. I don't have a alcohol...

    I don't have E85 tables. I don't have a alcohol content sensor. Wish I did.
    As I said I switched back to E85 a couple of tanks ago. Taking to long to relearn.

    HOW do I reset klf
  21. Replies
    13
    Views
    6,944

    Went from 87 octane to E85. How do I reset my...

    Went from 87 octane to E85. How do I reset my knock learn? It seems to be taking weeks to do it automatically
  22. Replies
    10
    Views
    6,667

    I'd like to know this also. And how do I force...

    I'd like to know this also.
    And how do I force the ecm back to the hi table
  23. Replies
    10
    Views
    6,667

    Really, that's good to know. I've been trying to...

    Really, that's good to know. I've been trying to figure out how to reset back to the high octane table after having cleared up a high timing problem
  24. Copy... So I'm guessing tuning the VVE is...

    Copy... So I'm guessing tuning the VVE is mandatory along with the changes in the MAF I'll need for the cam?
  25. Or variable volumetric efficiency? Damn, really?

    Or variable volumetric efficiency? Damn, really?
Results 1 to 25 of 121
Page 1 of 5 1 2 3 4