Search:

Type: Posts; User: tlavoie87

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    191

    i have the same cams and a tune i can do a remote...

    i have the same cams and a tune i can do a remote tune for 250
  2. i have also down this with a TCM loosing voltage...

    i have also down this with a TCM loosing voltage always have a trickle charger connected when flashing just to be safe
  3. any update on this.. pointers with cam angles ?

    any update on this.. pointers with cam angles ?
  4. Replies
    3
    Views
    457

    comming from experience i personally have swapped...

    comming from experience i personally have swapped out the LLT E69 bosch ecu for the new 2015 LFX and E39A Delphi ecu with zero issues.. this was done with my 2010 Camaro.. there are some changed and...
  5. Replies
    2
    Views
    253

    What's your email I'll send you a good channels...

    What's your email I'll send you a good channels file to log appropriate pids.. most of the time if the throttle is closing the driver demand table map a will fix it
  6. Replies
    1
    Views
    114

    you can read as many times as you want with out...

    you can read as many times as you want with out using credits its when you write were it needs the credits..
  7. Replies
    3
    Views
    235

    thanks Cobalt thats what ive been doing is going...

    thanks Cobalt thats what ive been doing is going by the AEM i also have my torqbyte meth controller on the same source and its reading the same as the AEM so im thinking the MAP is the issue .. gonna...
  8. Replies
    3
    Views
    235

    Boost readings

    Ok so I am in a bit of a dilema I'm getting 2 different readings for boost one with the map and one with my aem digital boost guage which has 5volt output for logging both are sourced from the...
  9. Replies
    14
    Views
    1,070

    send me a PM

    send me a PM
  10. Replies
    14
    Views
    1,070

    im using a 3bar but run maf only

    im using a 3bar but run maf only
  11. What benefits or additional tables are you seeing...

    What benefits or additional tables are you seeing with tiny tuner i have an E39A Twin Turboed Camaro and interested if i should give it a shot thanks
  12. Replies
    3
    Views
    315

    https://www.rdpstore.com/p-2326-gm-3-bar-map-senso...

    https://www.rdpstore.com/p-2326-gm-3-bar-map-sensor-12592525-camaro-corvette-zr1.aspx

    correct MAP and Offset numbers .. with the Colorado and LFX your gonna want to tune it for Maf only thats how...
  13. Replies
    3
    Views
    205

    use these channels and do a log87750

    use these channels and do a log87750
  14. Replies
    14
    Views
    1,070

    will try i did some Maf and VVE tuning and got it...

    will try i did some Maf and VVE tuning and got it to idle around 0-4 degrees which is decent was better than the -5--10 degrees
  15. Replies
    57
    Views
    6,879

    Higgs dumb question nut how do you tune zero...

    Higgs dumb question nut how do you tune zero pedal external load? what should i be loggng or charting
  16. Replies
    3
    Views
    374

    i did its in the first post

    i did its in the first post
  17. Replies
    14
    Views
    1,070

    jquequezana how is your idle.. i cant seem to get...

    jquequezana how is your idle.. i cant seem to get rid of negative timing i have tried just about everything
  18. Replies
    57
    Views
    6,879

    ok so i did what you suggested removing from my...

    ok so i did what you suggested removing from my maf table and it now fluctuates attached a log86942
  19. Replies
    57
    Views
    6,879

    any update on this im having the exact same issue...

    any update on this im having the exact same issue mind you its on a different Engine but same exact Issue .. ive tried to lower Virtual Torque ..raise it same no change.. my STFT are wll within 3% .....
  20. Replies
    3
    Views
    374

    Bump anyone??

    Bump anyone??
  21. Replies
    3
    Views
    374

    Twin turbo LFX

    Good morning .. just finished up installing overkill Cams and twin turbo on my 2010 Camaro V6 .. i have swapped out the LLT for an LFX with a Delphi ECU .. the cams are mace profile with an overdrive...
  22. Replies
    8
    Views
    2,175

    hey scott any update ? i got a set on the way...

    hey scott any update ? i got a set on the way myself
  23. Replies
    14
    Views
    1,070

    14-15 psi .. .83 Lambda also spraying meth i got...

    14-15 psi .. .83 Lambda also spraying meth i got a set ove mace cams with an overdrive Fuel lobe on the Way now
  24. Replies
    14
    Views
    1,070

    hey man have you made any progress on this im in...

    hey man have you made any progress on this im in the process of tuning my Twin Turbo not sure if you have updated your tune since
  25. is this the same procedure for the 2014 Camaro v6...

    is this the same procedure for the 2014 Camaro v6 E39
Results 1 to 25 of 66
Page 1 of 3 1 2 3