Search:

Type: Posts; User: always last

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    2,962

    Thanks for answering. I was getting a complex. ...

    Thanks for answering. I was getting a complex.

    I did flash it back to stock using the write entire. But no change.

    I also did a write entire with the 1Bar SD I was using. Still no change.
    ...
  2. Replies
    6
    Views
    2,962

    84 hits and no replies. WOW Did I do something...

    84 hits and no replies. WOW Did I do something wrong.

    Any thoughts.

    Anyone.....
  3. Replies
    2
    Views
    2,969

    One vcm Two license

    My question is, can this VCM be licensed again. It has already been licensed by me once before. It is the second one in the list.
    If you notice on the bottom of the page I have the vin to my truck...
  4. Replies
    6
    Views
    2,962

    Readiness Status

    The only way I can see to turn these on would be in the Engine Diagnostics. But from what I see there already on.

    The part I don't understand is the N/A. I would think it would say incomplete or...
  5. Replies
    6
    Views
    2,962

    Readiness staus question

    I have a question on the readiness status. If you look at the pic below you can see everything says N/A except one.
    33252
    Here is some info on the VCM
    33253
    My question is can I turn these on.
  6. Replies
    220
    Views
    122,886

    Very cool

    Very cool
  7. Replies
    37
    Views
    14,002

    I ripped both my Lc1 XD-16 setups out with a set...

    I ripped both my Lc1 XD-16 setups out with a set of cutters and a hard pull. I wasn't nice about it. There was nothing left but a pile of wasted money on the floor in a lot of little pieces. To...
  8. Replies
    0
    Views
    1,213

    Check out these numbers.

    I was asked to look at a 04 GMC 4x4 8.1 with an allison 5 speed. He said it felt a little flat when he jumped on it. I plugged in the scanner and told him to go for a ride. Here are the results. WOW...
  9. Thread: Its a Boy!

    by always last
    Replies
    46
    Views
    20,308

    No HP Tuner Hat. Whats up with that. Congrats...

    No HP Tuner Hat. Whats up with that. Congrats Bill.
  10. Thread: Locking up

    by always last
    Replies
    4
    Views
    2,370

    I'll send the info.

    I'll send the info.
  11. Thread: Locking up

    by always last
    Replies
    4
    Views
    2,370

    New Toshiba with Vista Home used only to tune. 9...

    New Toshiba with Vista Home used only to tune. 9 month or so with no problems.
    AMD Turion 64x2 1.90GHz
    2.00 GB
    32 Bit

    Scanner doesn't lock up on my ride.

    Ran the default pids after it locked...
  12. Thread: Locking up

    by always last
    Replies
    4
    Views
    2,370

    Locking up

    I'm Trying to tune a GMC 3500 - 8.1 with an allison trany. The scanner keeps locking up when I'm trying to log. I can hit the stop button and then start it back up. It may make it threw the the...
  13. Replies
    9
    Views
    9,323

    Thank you.

    Thank you.
  14. Replies
    9
    Views
    9,323

    Would that be flow rate vs kpa. Because that...

    Would that be flow rate vs kpa. Because that shows 24.25
  15. Replies
    9
    Views
    9,323

    Thanks 98Camarod. I found on line the cc/min is...

    Thanks 98Camarod. I found on line the cc/min is 226 which coverts to 21.53 lbs. The dealer thinks there 22lbs but there not sure. I'm going to roll with the 22lbs for now and see what happens, but I...
  16. Replies
    9
    Views
    9,323

    Injector question

    Can anyone tell me the ?lbs/hr of these injectors. (Delphi 25320288) They came in a 2000 6.0 silverado. I need the info so I can update the injector field in HPT. I looked on the web and can find...
  17. Replies
    15
    Views
    8,395

    Misfire only

    Misfire only
  18. Replies
    5
    Views
    2,995

    Bill. I just ordered the Learn at Home coarse...

    Bill. I just ordered the Learn at Home coarse from The Tuning School. No classes in the Boston Ma area. Any comments on the book?
  19. Replies
    5
    Views
    2,995

    I bit the bullet today and did a write entire and...

    I bit the bullet today and did a write entire and I'm back to normal. That write entire button scares me, It's kicked my ass twice. This time it worked out.
  20. Replies
    5
    Views
    2,995

    I've been using it with no problems. Load the 1b...

    I've been using it with no problems. Load the 1b SD file. Start the scanner-hit the wrench- start the sd and away we go. General tab is turned on for vetpsve. You know the history with my vcm's....
  21. Replies
    5
    Views
    2,995

    Check this out for me.

    This looks like a software problem. Reload the HP disk and I should be fine. But with two VCM's already unusable, I'm not making a move without asking. Everything works fine except the real time....
  22. Replies
    38
    Views
    22,928

    I was self employed for over 20 years and loved...

    I was self employed for over 20 years and loved it. Then the kids came and the need for a normal life.

    The business did great but I was never home. I only worked on class 8 trucks and the shop...
  23. Replies
    45
    Views
    20,586

    It's kind of the sign of our time, really. People...

    It's kind of the sign of our time, really. People have fallen into the habit of instant gratification and lose the stomach to get there hands dirty and put in the time and hard work it takes to...
  24. Replies
    38
    Views
    22,928

    Good luck Doug, Because of you I'm no longer...

    Good luck Doug, Because of you I'm no longer stuck in 1st, I made it all the way to overdrive and it was a proud moment lol.
  25. Replies
    121
    Views
    73,836

    My os is 127012, The motor is a 6.0 4l80 out...

    My os is 127012,

    The motor is a 6.0 4l80 out of a 2000 2500 HD from the bone yard. I'm also running the vcm that came with the bone yard motor and trany. I posted a run I made. You'll see that...
Results 1 to 25 of 66
Page 1 of 3 1 2 3