Search:

Type: Posts; User: Rodsctsv

Search: Search took 0.00 seconds.

  1. Replies
    12
    Views
    12,773

    No image

    No image
  2. Replies
    1
    Views
    916

    No start after warm up

    So after the engine is at operating temp you can shut it off fill up or let it set for a few minutes and it will not start turns over fine , let it set for 15 or longer it fires wright up , Ive made...
  3. Replies
    3
    Views
    1,322

    Correct I do have headers , ok thx I will try that

    Correct I do have headers , ok thx I will try that
  4. Replies
    3
    Views
    1,322

    this is another log different tune

    this is another log different tune
  5. Replies
    3
    Views
    1,322

    Swinging AFR /stumble

    Changed air filter 2 months ago afr started swinging bad logged and changed the maf with the correction multiply% after a few weeks of doing still afr swings changed filter back still swinging and a...
  6. Replies
    21
    Views
    7,152

    I know most remote CTSV tuners , I'm on my 3rd ,...

    I know most remote CTSV tuners , I'm on my 3rd , I do most of the tuning now but still need help with the tranny
  7. Replies
    21
    Views
    7,152

    I run around 80 on lambda , 12 ctsv coupe with...

    I run around 80 on lambda , 12 ctsv coupe with FBO and E80 , I run the AEM 30-0333 and suggest switching to lambda,, 82 is a little lean on daily hits IMO mayb on trac days a few times . I'm at 75...
  8. Replies
    6
    Views
    1,801

    Doh , thx , ended up having to move the maf up...

    Doh , thx , ended up having to move the maf up and rescalen
  9. Replies
    6
    Views
    1,801

    74051 I changed air filter and from idle to...

    74051 I changed air filter and from idle to around 2000 RPM and less its erratic, I can reduce that down but Im lost where the idle airflow is
    74052
  10. Replies
    6
    Views
    1,801

    74050 Ok got it , I need to know where is the...

    74050 Ok got it , I need to know where is the idle airflow its reworded in 3.6
  11. Replies
    6
    Views
    1,801

    I took a screen shot of the aiflow tab but...

    I took a screen shot of the aiflow tab
    but keeps giving me an error when uploading
  12. Replies
    6
    Views
    1,801

    where is the idle airflow in the 3.6 ?

    All the vids on youtube shows a idle airflow but mine desnt show can someone circle the idle airflow in 3.6 thx
  13. Thread: U0109 code

    by Rodsctsv
    Replies
    0
    Views
    901

    U0109 code

    I removed a jms bap , and was in the middle of installing a dsx pump , I went to drive the car and to get some fuel out but it would just turn over , I'm getting a U0109 lost communication with fuel...
  14. Replies
    0
    Views
    769

    FP loss in middle of run

    Made some runs last night and first pass was a little rich lambda average was .73 so I leaned it up and I thought it was to much lambda average was.81 so I put some more fuel back in and enriched the...
  15. Replies
    6
    Views
    2,275

    Ok thx for the response , I have a 5in CAI with...

    Ok thx for the response , I have a 5in CAI with matching MAF , I was hoping that was not maxed out , I'm on E85 with 1000 ID injectors , along with dual nozzle meth injection , thx for your input
  16. Replies
    6
    Views
    2,275

    I feel dumb , I see it now during the small burn...

    I feel dumb , I see it now during the small burn out then again in 2nd going in to 3rd , I dunno why I didn't earlier ok thx , also here is another run about 30 minutes later from a older tune I...
  17. Replies
    6
    Views
    2,275

    Where is the knock ?

    My tuner says there is knock , I don't see it in the log can someone point this out ? during the pull
  18. Replies
    0
    Views
    810

    FP and timing on this log ?

    Mods on a ctsv 8.66 lower 2.38 upper 90mm tb LT headers, 1000ID injs 5" CAI E85 and dual nozzle meth pre/post . My FP seems a little low with the JMS at 18v ((verified with meter )) its around 52...
Results 1 to 18 of 18