Search:

Type: Posts; User: partemisio

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    3,404

    Can't connect laptop to interface

    I have emailed support already. I know it's the weekend though and would expect to not hear anything till Monday though so that's why I'm looking for help on here. Below is what I sent support.

    "I...
  2. Replies
    8
    Views
    2,681

    I just got it to fire. Another guy recommended I...

    I just got it to fire. Another guy recommended I try "write entire" and I did and then it fired up. I will disable those dtc's that you mentioned also. Thanks for the help!!!
  3. Replies
    8
    Views
    2,681

    Thanks for the response. Here is my most recent...

    Thanks for the response. Here is my most recent one where I think I've done all of what you mentioned. I may have missed something though cause still same issue, crank no start.87704
  4. Replies
    8
    Views
    2,681

    Help with crank no start

    As the title suggests, I have a crank no start with my car and I'm not sure why but it's got to be something with the tune. I previously had AEM stand alone on the car until that blew a sensor ground...
  5. Replies
    7
    Views
    6,313

    Nobody can help?

    Nobody can help?
  6. Replies
    7
    Views
    6,313

    The computer is out of a 2000 suburban. I have it...

    The computer is out of a 2000 suburban. I have it in my lq4 swapped 240sx. I'm not understanding what that table shows exactly. The number I can edit looks like the temperature itself. How am I...
  7. Replies
    7
    Views
    6,313

    Changing IAT specs

    I have an aftermarket IAT sensor. The link below shows the calibration info for it. I have found the "iat sensor curve" in hptuners software but am not sure what the values mean. I'm sure the...
  8. Replies
    11
    Views
    18,236

    Forgot I have an aftermarket IAT sensor also. The...

    Forgot I have an aftermarket IAT sensor also. The link below shows the calibration info for it. I have found the "iat sensor curve" in hptuners software but am not sure what the values mean. I'm sure...
  9. Replies
    11
    Views
    18,236

    In regards to the wideband, can I just put the...

    In regards to the wideband, can I just put the pins where one of the factory front o2 wires go into the computer so that I can run closed loop off it and log it?
  10. Replies
    11
    Views
    18,236

    Thank you!!! You have been a great help.

    Thank you!!! You have been a great help.
  11. Replies
    11
    Views
    18,236

    Thank you!!! You have been a great help.

    Thank you!!! You have been a great help.
  12. Replies
    11
    Views
    18,236

    Here's the completely stock tune. I need to set...

    Here's the completely stock tune. I need to set it up for the 80lb injectors, 3 bar map sensor, and no maf. The car also has no o2 right now so before I just had it running off open loop. 73383
  13. Replies
    11
    Views
    18,236

    Ok, I will post the stock file tomorrow when I am...

    Ok, I will post the stock file tomorrow when I am at the car. I'll pull the wiring diagram for the truck I got the PCM out of and see what pins to use. Learning this software is a lot different than...
  14. Replies
    11
    Views
    18,236

    I forgot to mention that, I do plan on running...

    I forgot to mention that, I do plan on running speed density cause I don't run a maf with the turbo. I believe it is the standard version.
  15. Replies
    11
    Views
    18,236

    Setting up 3 bar map sensor and wideband

    I have the following map sensor and was wondering how I set it up for my car? I am trying to get the car running now with HPTuners. It had an AEM stand alone before but the board on it got burnt up...
Results 1 to 15 of 15