Search:

Type: Posts; User: Rbelar21

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    168
    Views
    36,817

    Metro, to answer literally the first question you...

    Metro, to answer literally the first question you asked (after tuning up to this point) at high 5k rpm's i am flowing almost 40
  2. Replies
    168
    Views
    36,817

    Anyone find that they have more knock when...

    Anyone find that they have more knock when utilizing the Knock Sensors to allow timing rather than the Octane Adjustment via the blend factor?

    Interestingly, when i add the timing directly via...
  3. Replies
    168
    Views
    36,817

    That 100% helps getting higher load! Thanks a ton...

    That 100% helps getting higher load! Thanks a ton for the help earlier.

    I notice now that the LSPI tables are my limit which is what I was trying to do. Hit almost 2.6 load and also structured my...
  4. Replies
    168
    Views
    36,817

    Wonderful thanks a lot man! I'll let you know how...

    Wonderful thanks a lot man! I'll let you know how it goes.
  5. Replies
    168
    Views
    36,817

    Hey all - hope you are all well, just wanted to...

    Hey all - hope you are all well, just wanted to post a quick snip of the truck and where i am at now for a WOT pull and get some criticism if possible. I feel like I finally got it to the point that...
  6. Agreed, I have it down lower to begin with...

    Agreed, I have it down lower to begin with because surprisingly the stock map actually would constantly hit knock and come back down. then go up and hit it again. I am on team any knock is bad.
  7. Yeah - updating the recovery rate defintely made...

    Yeah - updating the recovery rate defintely made the dynamic timing run up quicker and i can see knock is still registered. I wonder if anyone has any insight on how detrimental this can be or if the...
  8. Can anyone explain the recovery rate tables? ...

    Can anyone explain the recovery rate tables?

    Do they also impact how knock is registered / held?
  9. Is there a table that it stores those "best case"...

    Is there a table that it stores those "best case" values? even if it went away after key cycle? I thought it just did what you told it to and the only modifier technically is the OAR.
  10. Max Advance Vs Borderline Correction (Octane Adjustment)

    Does anyone have any insight into how sensitive the knock sensors are when it comes to Dynamic Advance (max advance) in comparison to the Borderline corrections, or is it all the same?

    I guess...
  11. Replies
    168
    Views
    36,817

    Is there anyway to get more resolution to limit...

    Is there anyway to get more resolution to limit timing by IAT or MCT? or am i limited to the IAT compensation only?
  12. Replies
    168
    Views
    36,817

    Thank you sir - I'll take a look into it and see...

    Thank you sir - I'll take a look into it and see if i want to extend it out. I think to make real power out of it I will have to do it, haha.
  13. Replies
    168
    Views
    36,817

    Meaning the torque model i posted above? or is...

    Meaning the torque model i posted above? or is that a seperate table.

    Sorry for my ignorance on this, was trying to get to the max without touching modeling but it seems like if i want more i have...
  14. Replies
    168
    Views
    36,817

    Do you mean if i am at 2.32-2.38 like in my log...

    Do you mean if i am at 2.32-2.38 like in my log at Higher RPM, it wont be somewhere between 2.0 and 2.4 from the Torque Model and it will be closer to the 2.0?

    Do i need more resolution?
  15. Replies
    168
    Views
    36,817

    They extend to 2.4, yes. Attached is mapped point...

    They extend to 2.4, yes. Attached is mapped point 0 & 11 which are the highest percentages at this RPM range.

    To that point, it seems like it is farily close to the 2.0 load range... but wouldnt...
  16. Replies
    168
    Views
    36,817

    Hey All, Hope everyone is well. I have a quick...

    Hey All,

    Hope everyone is well. I have a quick question. I have got load to come up properly at higher RPM and it is feeling very very strong.

    However, I am noticing that brake torque is still...
  17. Replies
    168
    Views
    36,817

    Here is the log - it always seems to be when i am...

    Here is the log - it always seems to be when i am going up a hill and there are consistent torque requests. You can see i was cruising and then floored it, the hill is fairly big.

    126995

    EDIT:...
  18. Replies
    168
    Views
    36,817

    Anyone have any issues with FMEM Pedal Follower?...

    Anyone have any issues with FMEM Pedal Follower? I have had this come up a few times and it just immediately goes into limp mode. Usually seems to be at higher pedal requests? after restarting truck...
  19. Replies
    168
    Views
    36,817

    Yeah its an odd feeling. On one hand I am putting...

    Yeah its an odd feeling. On one hand I am putting a lot of faith in Ford and can just let the knock happen (and they are way smarter than me obviously), but then on the other hand I really really...
  20. Replies
    168
    Views
    36,817

    I think that brings up a good point, and a more...

    I think that brings up a good point, and a more technical one at that. If you notice my logs above - regardless of knock mode, is it worth doing cyl compensations to try to get them all the best...
  21. Replies
    168
    Views
    36,817

    hmmm okay - thanks for the response.

    hmmm okay - thanks for the response.
  22. Replies
    168
    Views
    36,817

    Has anyone messed with Per Cyl vs Global timing?...

    Has anyone messed with Per Cyl vs Global timing? I would assume that per cyl is more "efficient" but do we understand how global reacts? does it err on the side of caution and go with lowest / first...
  23. Replies
    168
    Views
    36,817

    Backing the dynamic advanced down and pulling a...

    Backing the dynamic advanced down and pulling a degree from the borderline octane table definitely put it in an area where i feel comfortable.
  24. Replies
    168
    Views
    36,817

    Ok, i think thats the route i am going to take...

    Ok, i think thats the route i am going to take for now anyway, is drop the dynamic advanced down a bit and get it closer. I guess i just have to get used to the per cyl.
  25. Replies
    168
    Views
    36,817

    There was a chance i was hitting a hill in these...

    There was a chance i was hitting a hill in these areas, I live in northern NJ so we have quite a few steep hills, even on route 80 where this was logged from.

    Mike, you are correct I see this even...
Results 1 to 25 of 103
Page 1 of 5 1 2 3 4