Search:

Type: Posts; User: rdubord

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    14
    Views
    687

    We had a similar issue, we had to change the...

    We had a similar issue, we had to change the crank sensor setting with HPT and it started right up.
  2. Replies
    0
    Views
    171

    2004 545-RFE Torque converter control?

    Have the HPT gods given us Torque converter control on the NGC3 non-can Rams?
  3. 2004 Ram 1500 5.7 goes full lean when put into gear in open loop

    As stated above. Cold start, everything is fine in park. Warm-up has normal enrichement up to the closed loop point 100 degrees. If the vehicle is put in gear or neutral, the wideband goes full lean...
  4. Replies
    2
    Views
    185

    After reloading the file a second time, all is...

    After reloading the file a second time, all is good.
    Thank you
  5. Replies
    2
    Views
    185

    LQ9 wiil not take any throttle

    LQ9 in a mud bogger, engine starts and idles fine. Fast idle when cold and slowly idles down as ect comes up. This is a cable throttle setup. I have gone into the file and put a 0 in the ETC block in...
  6. Replies
    2
    Views
    436

    Do the CNG vehicles have a different pcm, or...

    Do the CNG vehicles have a different pcm, or protocol? If not does anyone have a stock 2015 2500 5.7 4x4 file?
  7. Replies
    3
    Views
    519

    Not a lot available for 04, I have one. Hptuners...

    Not a lot available for 04, I have one. Hptuners doesn’t have a lot of love for the non can ngc3. You can’t firm shifts or change torque converter settings. Just shift points
    Rich
  8. Replies
    5
    Views
    623

    Diesel?

    Diesel?
  9. Replies
    2
    Views
    436

    I wonder if flashing it to a standard 2500 5.7...

    I wonder if flashing it to a standard 2500 5.7 would work?
  10. Replies
    2
    Views
    436

    2015 RAM 2500 CNG Delete

    no issue disabling the check engine codes, but how do I make the low (cng) fuel light not illuminate and also how do I get the engine to not try to use cng if the gauge is 'tricked'?
    Thanks,
    Rich...
  11. Thank you, I will give the above a try. Rich

    Thank you, I will give the above a try.
    Rich
  12. Added quite a bit of timing and she came to life

    Added quite a bit of timing and she came to life
  13. what i mean is i dont have the wideband in the...

    what i mean is i dont have the wideband in the scanner yet. can anyone help with idle?
  14. 97 Silverado 411 pcm swap runs good but a dog off the line

    i don't have the wideband hooked up. Truck runs great mid range and top end. idle afr is 14.5. what do i need to do to bring this 350 to life on the bottom end?
    Rich
  15. Replies
    3
    Views
    328

    well, thank you so much, i added stft and ltft to...

    well, thank you so much, i added stft and ltft to the left side and now can log them thanks!!!
  16. Replies
    3
    Views
    328

    thank you for the quick reply. I am kinda lost.

    thank you for the quick reply. I am kinda lost.
  17. Replies
    3
    Views
    328

    no fuel trims on 01 Express van tune

    As stated above, not getting fuel trims on 411 pcm with the 01 express van tune in a 97 silerado. please help me out.
    Rich
  18. Sticky: '04 Ram 5.7L 545-RFE torque converter control...

    '04 Ram 5.7L 545-RFE torque converter control please.
  19. Replies
    1,733
    Views
    472,170

    So no response to the ngc3 questions?

    So no response to the ngc3 questions?
  20. Replies
    1,733
    Views
    472,170

    When will we get Kr and TCC on the ram ngc3?

    When will we get Kr and TCC on the ram ngc3?
  21. Replies
    0
    Views
    742

    '04 5.7 Ram open loop question

    So 2004 Ram 5.7. I put it in open loop and when I put the transmission into drive or reverse, the scanner shows it to appear to be in closed loop. The scanner still shows OL, but the O2 sensor...
  22. Replies
    7
    Views
    2,133

    Well, emailed them, that didn't work. They don't...

    Well, emailed them, that didn't work. They don't have much intention of supporting TCC
  23. Replies
    2
    Views
    1,017

    You can tune the transmission shift points, you...

    You can tune the transmission shift points, you cannot tune the TCC (torque converter). I believe the '06 is like my '04 and Bill said that it would be quite awhile if we ever get it.
    EDIT: after...
  24. Replies
    7
    Views
    2,133

    ok, Thanks

    ok, Thanks
  25. Replies
    3
    Views
    1,326

    Non CAN NGC3 progress

    Hello, I know you guys are busy. Just wondering how the Non CAN NGC3 progress is going? Need to be able to log Knock, change gear ratio and speedo cal. Also looking for Torque converter lockup...
Results 1 to 25 of 86
Page 1 of 4 1 2 3 4