No luck with this so far. Licensed a file from the repository and tried to flash it into my setup and I fear I may have bricked the ECM. I will make a new post in the correct sub-forum with the...
Type: Posts; User: Tigre_loco
No luck with this so far. Licensed a file from the repository and tried to flash it into my setup and I fear I may have bricked the ECM. I will make a new post in the correct sub-forum with the...
Just got it fixed today. Turned out to be a mechanical issue inside the transmission.
Got it all put together and the trans now has forward movement but no speedo and no shifting. Feels like the...
I'm sure a scan log would be helpful. What parameters would be helpful in pin pointing the issue? I can get a log tomorrow.
Hey guys, I'm looking for some help on my 2005 Colorado LS6 swap. The truck was originally a 2.8L with the 4l60e. The input shaft on the trans was swapped to fit the 300mm shaft and harness, ECM...
Bump for further suggestions. At a loss here. Tried to get some VE tuning in last night only to get stranded while attempting to load the updated file then having to wait for the car to cool off...
Yeah the only DTC was for the MAF to ensure it is failed with the 2 Bar SD I hadn't deleted the code yet.
I was out of town for a few weeks so hadn't had a chance to mess with this much. I made some adjustments to the tables you recommended Dermotw. No change. I didn't have any issues firing the car up...
Bump
Hey guys I am having some issues with a car I'm working on. I'm hoping you all may be able to give me some help.
Car is a 2000 C5 with an ls3 stroker and A&A blower kit on the car. Tune is a 2...
Eric,
Do you still need more TCM reads? I've got 2 I can get you this weekend if you're still looking for some.
Hey everyone,
I just installed an LS3/LS7 card style maf sensor into my camaro. The car is a 1999 H/c/i ls3 stroker 6 speed car with 42lb Ford green tops. I am using the Banish injector data for...
Thanks for all your help guys. I got it finished up and running pretty damn good. Thanks for providing me the base tunes to work off of and getting me close Russ. James, I did play around with the...
James,
Here it is.
Thanks for everyone's input. I got the car back and have been working at the RAF tables. I've got the Idle trims nailed down and idling nicely now using Russ's base tune to start from. My IAC counts...
Thanks for the input everyone, I will try and get over to the car soon and try some of the suggested changes and see where it gets me. I'll keep you guys posted.
Yes, the car was in closed loop. Should I put it in open loop and reset the fuel trims while running the scanner? For what ever reason the LTIT are steady at -3.00g/sec P/N and -2.86g/sec Gear. And...
Hey Russ,
I got a chance to get over to the car and load your tune and run the scanner. The car started and idled great with the tune you provided (final-2). I ran the scanner while in P/N and...
Russ,
I replied to your post on ls1tech before I seen this here. I'll get the car back this week and load this tune and run the scanner. I'll post back with my results as soon as I get them....
I'm not sure I will look into that and see what I can come up with. Would it be the IAC steps vs. effective area table that I'd need to make changes to?
Hello everyone. I just finished up a build and the combo is as follows:
2002 Chevy Camaro A4 stock bottom end
PRC 227 heads 62cc's
TSP MS4 cam 239/242
Fast 102 with Nick Williams 102 TB
4l60e...
You will most likely need to adjust the offset. The LC1 might have a different offset than the MTX. Look for the correct info in the manual for your MTX.
Take a look here......
Awesome, thanks for the update.
Hey 5_Liter_Eater,
How are you liking that MTX?
I may not understand your question here, but the red wire from the AFX gets a keyed +12V and the two black wires get grounded. The wires that go to the interface are the yellow and brown wires from...
Cool project!