Search:

Type: Posts; User: Ghostnotes

Page 1 of 14 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    8
    Views
    396

    HUH? At this point I only have 2. One is lack...

    HUH?

    At this point I only have 2. One is lack of fuel which is fixable, the other is HPT does not seem to calculate coefficients correctly on some os's. The car runs great on MAF only. However if...
  2. Replies
    48
    Views
    3,123

    At this point I trust my ears,eyes seat of the...

    At this point I trust my ears,eyes seat of the pants etc. after making adjustments.
  3. Replies
    48
    Views
    3,123

    Thanks for replying. I just got back form an out...

    Thanks for replying. I just got back form an out of town job and will look into it. My cam is locked so I'm not messing with the overall camshaft angles. I would assume that to be correct since it...
  4. From what i understood,EOI was like a maximum you...

    From what i understood,EOI was like a maximum you wanted to go in cam degrees, 180 being the beginning of the power stroke.


    I get what you are saying since SOI is more relative to piston speed...
  5. 342 is my max according to my cam specs and the...

    342 is my max according to my cam specs and the EOI should never go past 180...cam degrees
  6. Replies
    48
    Views
    3,123

    Exact same, Same rpm breakpoints and same...

    Exact same,

    Same rpm breakpoints and same Pressure ratio breakpoints. I'm going to do a video later and post it up. If it's me, it's something probably obvious to everybody esle and I'm stuck on...
  7. Replies
    8
    Views
    396

    I get it but do think i read somewhere someone...

    I get it but do think i read somewhere someone was running 12.5 on 14.1 stoich sounded off to me.
    I have adjusted my SOI but not in that area so that rules that out.

    I guess I am at my limit...
  8. Replies
    8
    Views
    396

    I'm at 11.8 but i have read conflicting posts...

    I'm at 11.8 but i have read conflicting posts that says 12.5 is safe on DI as well.


    I've developed a little knock as well in the 3000rpm/80-90 airmass range, but i think i know what that is.It's...
  9. Replies
    8
    Views
    396

    5psi on stock LT1 fuel system

    I'm running stock bore/stroke with a YSi-V7. Stock bottom pulley with a 3.8 upper and at about 4500rpm i start getting above 5ms.

    Is this about right? I'm a few months away from my fuel upgrade....
  10. Replies
    48
    Views
    3,123

    One thing i just now noticed.... I'm running a...

    One thing i just now noticed....

    I'm running a 3 BAR MAP so i set my VE table accordingly. If I set it to a 1 BAR map the problem goes away but does me no good since I'm boosted.

    What am i...
  11. Replies
    48
    Views
    3,123

    Thanks for getting back. I kind of figured that...

    Thanks for getting back. I kind of figured that and I guess its something we can't really see. I always kind of figured that and thats why early on when i was copy/pasting so I would always copy a VE...
  12. Replies
    48
    Views
    3,123

    I just tried another round and still the same...

    I just tried another round and still the same problem. I can get my idle perfect, trims pretty much 0, timing steady at 17*, throttle good, torque matches. Take a small drive to gather error data,...
  13. Thread: licenseing

    by Ghostnotes
    Replies
    0
    Views
    86

    licenseing

    What would be gained by me if I licensed the rest of the systems since I have a manual?
  14. Replies
    48
    Views
    3,123

    My plan on a street VVE tune would to be to do a...

    My plan on a street VVE tune would to be to do a scan or 3 at say idle-2000, get that working then work up in maybe 500rpm increments. Worked in my real VE days.

    I am still having issues with this...
  15. Replies
    6
    Views
    197

    They are exactly the same. When I go from...

    They are exactly the same. When I go from standard to either 2 or 3 BAR, I copy the labels to match and get the pop up error. The log is from the error hist. It does not show it in my previous posts...
  16. Replies
    6
    Views
    197

    Thanks!!

    Thanks!!
  17. Replies
    5
    Views
    424

    I actually just traded it in for an Audi and I...

    I actually just traded it in for an Audi and I think I ditched the tune.

    I will check when I get home.
    I pulled my next door neighbor's tune before I traded mine and his was a 2.0T and I still...
  18. Replies
    2
    Views
    256

    I do and that was exactly the point. I went to...

    I do and that was exactly the point. I went to pull my tune and the comms saw it as another device....wonder if it would license it......LOL.
  19. Replies
    6
    Views
    197

    Anybody??

    Anybody??
  20. Replies
    6
    Views
    197

    Ok so I started all over. I took my good running...

    Ok so I started all over. I took my good running MAF tune and made the changes to a 3 bar setup, saved it, loaded it(write entire), started it up and ran a short idle scan. Copied the readings from...
  21. Replies
    6
    Views
    197

    Incomplete zones??

    I did not want to hijack a thread so i will post here. Not sure what the error is telling me. From what it looks like my rows and columns match but it is giving me a zone error i have never seen. I...
  22. I had one in my sons 202 2500HD. I punched it out...

    I had one in my sons 202 2500HD. I punched it out to a 572 it was a monster and the Allison 1000 had no problem with the extra power. The heads are absolute crap though.
  23. Replies
    4
    Views
    310

    I have had the same exact issue with high...

    I have had the same exact issue with high negative and positive numbers but my row's are already set above 1.0. Did that help for sure?
    I might have to relook at mine or start all over again. This...
  24. Replies
    7
    Views
    2,046

    Wow

    Wow
  25. Thread: Maf Tuning

    by Ghostnotes
    Replies
    3
    Views
    473

    Make sure you highlight the entire table in the...

    Make sure you highlight the entire table in the scanner, it should turn blue. Then copy. Next go to the editor highlight the entire table there, then multiply by%.
Results 1 to 25 of 327
Page 1 of 14 1 2 3 4