Search:

Type: Posts; User: JaegerWrenching

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    64

    Try and pull the tunes, worst case is it'll give...

    Try and pull the tunes, worst case is it'll give you an error. I have pulled tons of SCT tunes on mustangs which is around the same year so you can get lucky sometimes. Be sure to return your truck...
  2. Replies
    18
    Views
    487

    I think you are doing fantastic especially when...

    I think you are doing fantastic especially when you consider the tools you've been given to complete your task. You're doing everything right and i wouldn't change anything. Keep an eye on BP ratio...
  3. Replies
    18
    Views
    487

    You can advance the timing in it to more than...

    You can advance the timing in it to more than they have in their write up and you're going to end up around 26-29* BTDC. EGT's will drop while increasing timing gradually until peak cylinder pressure...
  4. Can you post your tune? It's tough to say without...

    Can you post your tune? It's tough to say without being able to view your current settings and a data log to go with.
  5. Try playing with clutch fill time after setting...

    Try playing with clutch fill time after setting your OSS slightly higher or get the converter to lock 100% before the shift and see how clutch fill affects it. Remember if the clutch fill is set to a...
  6. No he's saying your input into the transmission...

    No he's saying your input into the transmission is the Turbine speed. The turbine is driven by the Impeller which is bolted to the flex plate and always the same as engine RPM. Turbine speed is what...
  7. In these videos do you have torque reduction...

    In these videos do you have torque reduction enabled still but set to a torque limit it won't reach or do you have it disabled?94992
  8. Replies
    4
    Views
    108

    You can use Forscan in the later trucks to...

    You can use Forscan in the later trucks to correct this issue. But there was only so much room for correction before it'd throw a code. I think someone did solve this problem but not 100% sure.
  9. 94989 This is what i kept seeing when trying to...

    94989 This is what i kept seeing when trying to get the tune from the repository.
  10. Awesome that's good to know and I appreciate the...

    Awesome that's good to know and I appreciate the update and response, I'm sure there are guys lining up to get subie help.
  11. Replies
    0
    Views
    56

    Trans PID's 17+ 6.7L

    Anyone have any luck getting the trans PID's to work on these 17+ trucks? 94975
  12. Can you post both tunes? i couldn't find any 7.3L...

    Can you post both tunes? i couldn't find any 7.3L diesel tune.
  13. I have this same issue on my 2018 f250 with a...

    I have this same issue on my 2018 f250 with a 6r140, I can't log the required tables to know if my changes are doing as intended because the 6r140 is not nearly as supported as the 6r80... and i...
  14. Replies
    18
    Views
    487

    The modes are probably injection configurations...

    The modes are probably injection configurations based on many factors, from engine temp, Cold, warm, hot, to intake air temp, again cold, warm, hot, to fuel pressure Low, med, high. You're probably...
  15. Looking for a stock Fx-50 tune file.

    Does anyone have a stock FX-50 tune file? I'd like to review the file to see what the tables look like and how it fuels. It's been almost two weeks since i sent my file in so i'm assuming they are...
  16. This sounds like a DPF was removed and it was...

    This sounds like a DPF was removed and it was tuned for the DPF/EGR being removed and now it's seeing the parts are missing because you flashed it back to stock. Were you able to download the stock...
  17. Does it have the DPF intact? have you read the...

    Does it have the DPF intact? have you read the engine codes to see what errors the ECM is throwing?
  18. Replies
    5
    Views
    405

    1A-2M is for shifting under 3 or 4 mph if i...

    1A-2M is for shifting under 3 or 4 mph if i remember correctly. Therefore it is of no use when looking to firm up WOT shifting because you'd be past that MPH and that table will not be in use. So...
  19. That makes perfect sense after reviewing the log...

    That makes perfect sense after reviewing the log as to why it does what it does now that you've explained this. This is also very good information to know on these ECU's. Thank you Jim. Btw is your...
  20. Replies
    13
    Views
    562

    My issue is , i'm simply asking for EGR maps...

    My issue is , i'm simply asking for EGR maps which we had and are required to dial in a tune and keep it within legal specs. How can i adjust my NOx production without being able to modify the EGR...
  21. 94688 These two areas circled are probably the...

    94688 These two areas circled are probably the main culprits of this issue. Now there is a slight delay on the channle's side of the data log which makes it harder to see exactly when it's happening....
  22. Replies
    13
    Views
    562

    What is a good option for Ford diesels?

    What is a good option for Ford diesels?
  23. Looks good, and rowing some gears!

    Looks good, and rowing some gears!
  24. Replies
    13
    Views
    562

    Where did the EGR maps go?

    When did the EGR maps disappear for the 6.7L Ford diesels? We had them a little while back and now they are gone. These are required for proper tuning with emissions intact.....
  25. This is very true! you just gotta learn and try...

    This is very true! you just gotta learn and try things. Nothing is better than making some changes data logging and seeing what happens, if you don't like your change undo it and try something else.
Results 1 to 25 of 138
Page 1 of 6 1 2 3 4