Search:

Type: Posts; User: Thatwhite5.0

Page 1 of 20 1 2 3 4

Search: Search took 0.00 seconds.

  1. Instead of trying to increase the prime time, try...

    Instead of trying to increase the prime time, try increasing the Cranking Fuel Mass by 5 or 10% in Fuel > General.
  2. Replies
    1
    Views
    342

    Successful relearn with the scanner

    I know a lot of people have issues with crank relearn function on the scanner. Most would show successful but would not fix the issue
    Had a 2016 Mustang GT throwing P0315 after a rebuild and clutch...
  3. There are so many ways to run the imrc delete and...

    There are so many ways to run the imrc delete and have it run correct or like stock
  4. Is there anything in the drop down box to select...

    Is there anything in the drop down box to select next to hardware?
  5. The injector data you have is correct. You can...

    The injector data you have is correct. You can leave it at that. Your fuel trims really don't look that bad for narrrowbands. I usually disable the LTFT to dial in fuel and they end up staying...
  6. Replies
    4
    Views
    623

    Adjust your torque ratios for what you're trying...

    Adjust your torque ratios for what you're trying to manage, DFSO is what it's called in the ratio tables. Deceleration Fuel Shut Off in fuel torque ratio and spark torque ratio. Thresholds in the...
  7. Replies
    15
    Views
    1,191

    How are you going to make the injector smaller?

    How are you going to make the injector smaller?
  8. Replies
    4
    Views
    623

    Adjust your torque ratios. Is spark retarding...

    Adjust your torque ratios.
    Is spark retarding to single digits or less than 20* during decel?
  9. There sure is a way to disable it. Most things...

    There sure is a way to disable it. Most things are right in front of you.

    138538
  10. Replies
    2
    Views
    343

    Automatic or manual? Well, here's one for a...

    Automatic or manual?

    Well, here's one for a MT82. You can open it and add the MP Weights if you wanted.
    138535
  11. Slip is TCC apply, unlock is TCC release. You...

    Slip is TCC apply, unlock is TCC release.
    You can calculate engine speed from the oss using transmission gear ratios and oss and make a spreadsheet for shift points.
    You said 3rd locks halfway...
  12. Replies
    3
    Views
    652

    That's the max angle in the throttle body model...

    That's the max angle in the throttle body model as well. If it could go more than 82*, I don't see there being any increase or benefit.
  13. Setting Fuel Torque Ratio's to 1.0 give's the...

    Setting Fuel Torque Ratio's to 1.0 give's the abililty to cut fuel, which is what you want in DFCO and to get rid of the backfires.. You're getting retarded spark during deceleration causing...
  14. Replies
    6
    Views
    679

    Yes, that's launch. Command MP1 or MP15 if...

    Yes, that's launch. Command MP1 or MP15 if running MP14+
  15. Replies
    12
    Views
    1,007

    Post your tune and datalog.

    Post your tune and datalog.
  16. Using the F150 is a good starting point to figure...

    Using the F150 is a good starting point to figure out how FF works, it's just that they have complete different BLK and MBT tables.. You'll end up doing what Mike said and maxing out the cylinder...
  17. He needs to tune his stock file instead of using...

    He needs to tune his stock file instead of using roush.
  18. Replies
    2
    Views
    672

    Lightnings have never been supported. The oldest...

    Lightnings have never been supported. The oldest gas truck is the 2004 F150.
    The Cobras are supported still with MPVI2, they have a different ECM than the SVT F150.
  19. Disable the oscillation switch or shuffle...

    Disable the oscillation switch or shuffle switch..
    You have the gt350 data but you also need to use the ETC Idle Throttle Angle from the gt350.
    To fix your main issue you asked bout, you need...
  20. Replies
    10
    Views
    1,014

    Yes you can tune it as long as you have both keys...

    Yes you can tune it as long as you have both keys in your tune file.
  21. If it's your car, tune the car to drive the way...

    If it's your car, tune the car to drive the way you want it to drive. The shift schedule never goes untouched. Disable torque based shifting and anticipation and tune it. If you wanted it to be...
  22. Replies
    15
    Views
    1,677

    Your spark tables are way too advanced. What is...

    Your spark tables are way too advanced. What is this swapped into? Curiosity.

    Do you have your stock file?
  23. You still have limiters set to 7000 Rpm. If...

    You still have limiters set to 7000 Rpm.
    If you want better drivability, scale the shift schedule up to your new shift points, 6800 to 7800. The shifts less than wot would need adjusting. If you...
  24. Replies
    15
    Views
    1,677

    Post your tune and what you're trying to...

    Post your tune and what you're trying to accomplish. You can get an idea of what MP you're in by the distance tables, then Rpm and air load from your datalogs.
  25. You need to increase the Rpm limiters in the...

    You need to increase the Rpm limiters in the transmission tab and increase your shift map which is scheduled to shift at around 6800.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4